journal article·2019-12

An investigation on fatigue life evaluation and crack initiation of Al-GFRP bonded lap joints under four-point bending

Pedram Zamani, Abdolrahman Jaamialahmadi, Lucas F.M. da Silva, Khalil Farhangdoost

Publisher page

Abstract

Abstract In this paper, fatigue life and crack initiation of aluminum-GFRP bonded lap joints are investigated under four-point bending loading. For this purpose, a new fixture was designed and constructed. Fatigue loads vs. number of cycles to failure (L-N) were obtained so that the influence of various load ratios on L-N were examined. Furthuremore, the load amplitude vs. number of cycle curves were investigated. In addition, the load amplitude vs. mean load curve was obtained at 100,000 cycles. The effect of different maximum fatigue loads and load ratios were investigated on crack initiation life by implementing the backface strain (BFS) measurement and using an optical microscope. From the results, it can be inferred that the life of the crack initiation phase is nearly equal to that of half of the total life for a maximum load of 50% of the static failure load, whereas it is negligible for maximum fatigue loads higher than 60% of the static failure load. It was found that for a load ratio of R = −1, the crack initiation phase is negligible. Moreover, It was found that BFS plots were ended to the L-N curve, and this curve could be considered as a limit for BFS plots. Finally, a combined diagram including L-N curve, BFS, initiation, and rapid failure curves can be used to predict the remaining life of a joint which is loaded up to a certain number of cycles.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Mechanical Behavior of Composites · Structural Behavior of Reinforced Concrete · Fatigue and fracture mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. da Silva · 2018
2. Influence of dissimilar composite adherends on the mechanical adhesion of bonded joints for small blade wind turbine applications10.1016/j.ijadhadh.2018.02.018 ↗
3. Adhesive joints with improved mechanical properties for aerospace applications10.1016/j.ijadhadh.2017.03.012 ↗
4. Pizzi · 2018
5. Advanced composites for the body and chassis of a production high performance car10.1504/IJVD.2007.013641 ↗
6. Tests of deck-to-hull adhesive joints in GFRP boats10.1016/j.engfailanal.2006.02.012 ↗
7. Mechanical behavior and failure modes of metal to composite adhesive joints for nautical applications10.1007/s00170-010-2866-1 ↗
8. An experimental investigation of static load capacity of Al-GFRP adhesively bonded single lap and double butt lap joints10.1590/1679-78251760 ↗
9. Fatigue behaviour of composite adhesive lap joints10.1016/S0266-3538(02)00082-9 ↗
10. Fatigue performance and life estimation of automotive adhesive joints using a fracture mechanics approach10.1016/j.engfracmech.2017.01.005 ↗
11. Experimental investigation of the effects of adhesive defects on the single lap joint strength10.1016/j.ijadhadh.2017.08.005 ↗
12. Non-linear stress and failure analyses of adhesively-bonded joints subjected to a bending Moment10.1163/1568561042411286 ↗
13. Experimental and numerical analysis of single-lap joints for the automotive industry10.1016/j.ijadhadh.2008.09.001 ↗
14. Stiff and flexible adhesives bonding CFRP to masonry substrates-investigated in pull-off test and single-lap test10.1016/j.acme.2012.03.015 ↗
15. The behavior of single lap joints under bending loading10.1080/01694243.2012.761926 ↗
16. The effect of the spew fillet on an adhesively bonded single-lap joint subjected to bending moment10.1016/j.compositesb.2013.05.056 ↗
17. Strength of single lap joints with artificial defects10.1016/j.ijadhadh.2013.04.009 ↗
18. Functionally graded adhesive joints by using thermally expandable particles
19. Comparison of the mechanical behavior between stiff and flexible adhesive joints for the automotive industry10.1080/00218464.2010.482440 ↗
20. Fatigue performance of adhesively bonded single lap joints with non-flat sinusoid interfaces10.1111/ffe.12575 ↗
21. Environmental effect on the fatigue degradation of adhesive joints: a review10.1080/00218464.2016.1179117 ↗
22. Effect of interface non-flatness on the fatigue behavior of adhesively bonded single lap joints
23. Fatigue behavior and damage evolution of single bonded joints in composite materials10.1016/j.compscitech.2005.04.026 ↗
24. Influence of mechanical surface treatment on fatigue life of bonded joints10.1080/00218464.2015.1122531 ↗
25. Fatigue resistance of an aluminum one-component polyurethane adhesive joint for the automotive industry: effect of surface roughness and adhesive thickness10.1016/j.ijadhadh.2018.02.012 ↗
26. A backface strain technique for detecting fatigue crack initiation in adhesive joints10.1080/00218469508009975 ↗
27. Investigating fatigue damage evolution in adhesively bonded structures using backface strain measurement10.1080/00218460213835 ↗
28. Fatigue initiation in adhesively-bonded single-lap joints10.1163/156856107782313629 ↗
29. Wahab, An investigation into the crack initiation and propagation behavior of bonded single-lap joints using backface strain10.1016/j.ijadhadh.2008.07.008 ↗
30. Monitoring the fatigue crack growth behavior of composite joints using in situ 2D-digital camera correlation10.1080/00218464.2018.1562923 ↗
31. ASTM E8/E8M-16a, Standard Test Methods for Tension Testing of Metallic Materials, ASTM International, West Conshohocken, PA, 2016, www.astm.org.
32. ASTM D638-14, Standard Test Method for Tensile Properties of Plastics, ASTM International, West Conshohocken, PA, 2014, www.astm.org.
33. User’s guide, Reference number 02. 14_EN_EU, Surface preparation and pretreatments, Araldite Industrial Adhesives, Huntsman Corporation, Basel, Switzerland.
34. Technical data sheet, Araldite 2015, Huntsman Advanced Materials, Basel, Switzerland, (2007).