Drilling tool geometry evaluation for reinforced composite laminates
Source abstract
Abstract
In this work, a comparative study on different drill point geometries and feed rate for composite laminates drilling is presented. For this goal, thrust force monitoring during drilling, hole wall roughness measurement and delamination extension assessment after drilling is accomplished. Delamination is evaluated using enhanced radiography combined with a dedicated computational platform that integrates algorithms of image processing and analysis. An experimental procedure was planned and consequences were evaluated. Results show that a cautious combination of the factors involved, like drill tip geometry or feed rate, can promote the reduction of delamination damage.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced machining processes and optimization · Advanced Measurement and Metrology Techniques · Laser Material Processing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. Investigation of stresses in the orthogonal cutting of fibre-reinforced plastics
2. Effects of hole machining defects on strength and fatigue life of composite laminates10.1016/S1359-835X(96)00106-6 ↗
3. Machining of composite materials
4. Experimental analysis of drilling damage in thin carbon/epoxy plate using special drills10.1016/S1359-835X(00)00069-5 ↗
5. Machining parameters for an intelligent machining system for composite laminates Int10.1016/S0890-6955(99)00065-6 ↗
6. Drilling carbon fibre reinforced plastics manufactured by autoclave – experimental and statistical study10.1016/S0261-3069(03)00062-1 ↗
7. Effects of special drill bits on drilling-induced delamination of composite materials10.1016/j.ijmachtools.2005.10.004 ↗
8. Parametric study on thrust force of core drill10.1016/j.jmatprotec.2007.04.062 ↗
9. Damage analysis of carbon/epoxy plates after drilling10.1504/IJMPT.2008.018983 ↗
10. Drilling of composite structures10.1016/S0263-8223(01)00040-X ↗
11. Prediction of the location of delamination in the drilling of composite laminates10.1016/S0924-0136(97)00059-9 ↗
12. Delamination-free drilling of composite laminates10.1115/1.2902131 ↗
13. Delamination during drilling in composite laminates10.1115/1.2899580 ↗
14. A mechanical model for predicting critical thrust forces in drilling composite laminates10.1243/0954405011515235 ↗
15. The effect of chisel length and associated pilot hole on delamination when drilling composite materials10.1016/S0890-6955(03)00127-5 ↗
16. Critical thrust force at delamination propagation during drilling of angle-ply laminates10.1016/j.compstruct.2004.04.004 ↗
17. Chisel edge and pilot hole effects in drilling composite laminates10.1115/1.1448317 ↗
18. Effect of eccentricity of twist drill and candle stick drill on delamination in drilling composite materials10.1016/j.ijmachtools.2004.08.001 ↗
19. Taguchi analysis of delamination associated with various drill bits in drilling of composite material10.1016/j.ijmachtools.2004.02.019 ↗
20. Delamination onset prediction in mechanically fastened joints in composite laminates10.1177/002199839903301002 ↗
21. A progressive damage model for mechanically fastened joints in composite laminates10.1177/002199839903302402 ↗
22. Numerical prediction of delamination onset in carbon/epoxy composites drilling10.1016/j.engfracmech.2007.03.009 ↗
23. Some experimental investigations in the drilling of carbon fibre-reinforced plastic (CFRP) composite laminates10.1016/S0890-6955(96)00095-8 ↗
24. Delamination analysis of carbon fibre reinforced laminates: evaluation of a special step drill10.1016/j.compscitech.2009.01.025 ↗