Influence of rapid high-temperature processing on the interface of CF/PEEK, a quick and effective method for enhancing the IFSS
Source abstract
Abstract
This study explores the effect of rapid high-temperature processing on the interface of carbon fibre (CF) reinforced poly-ether-ether-ketone (PEEK). Specimens that have been thermally treated at slower and faster heating rates and specimens that have not been post-manufacturing treated (virgin) are examined with single fibre pull-out tests. A comparison between their interfacial shear strength (IFSS) and their failure modes takes place. Scanning electron microscopy is used to assess the surface morphology of the thermally treated specimens, and partly cross-polarised microscopy is employed to investigate the development of transcrystallinity. Furthermore, to identify the extent of thermal degradation the specimens are examined with attenuated total reflection Fourier transform infrared spectroscopy. At faster heating rates, an improved interfacial adhesion up to 25% is found at temperatures where a low-level thermal damage is induced. At higher temperatures and despite the increased thermal damage, an IFSS increase of up to 10% is still identified. This is due to the beneficial formation of thermal residual stresses upon rapid high-temperature processing and shows that these processing conditions could effectively serve for enhancing the interfacial adhesion of CF/PEEK.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Fiber-reinforced polymer composites · Mechanical Behavior of Composites · Tribology and Wear Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (43)
Show source-provided references
1. In-house recycling of carbon- and glass fibre-reinforced thermoplastic composite laminate waste into high-performance sheet materials10.1016/j.compositesa.2020.106110 ↗
2. Carbon nanotube enhanced carbon Fibre-Poly(ether ether ketone) interfaces in model hierarchical composites10.1016/j.compscitech.2022.109327 ↗
3. Investigation of the thermal decomposition and flammability of PEEK and its carbon and glass-fibre composites10.1016/j.polymdegradstab.2010.11.009 ↗
4. An inverse model for optimisation of laser heat flux distributions in an automated laser tape placement process for carbon-fibre/PEEK10.1016/j.compositesa.2016.05.034 ↗
5. Concurrent design and manufacture of a thermoplastic composite stiffener10.1016/j.compstruct.2019.01.033 ↗
6. Properties of a thermoplastic composite skin-stiffener interface in a stiffened structure manufactured by laser-assisted tape placement with in situ consolidation10.1016/j.compstruct.2019.02.011 ↗
7. Mechanical characterisation of carbon fibre–PEEK manufactured by laser-assisted automated-tape-placement and autoclave10.1016/j.compositesa.2014.10.003 ↗
8. Effect of voids and crystallinity on the interlaminar shear strength of in-situ manufactured CF/PEEK laminates using repass treatment10.1016/j.compscitech.2022.109448 ↗
9. Moderation of thermoplastic composite crystallinity and mechanical properties through in situ manufacturing and post-manufacturing tempering: Part 1 – mechanical characterisation10.1016/j.compositesa.2021.106286 ↗
10. Moderation of thermoplastic composite crystallinity and mechanical properties through in-situ manufacturing and post-manufacturing tempering: Part 2 – morphological characterisation10.1016/j.compositesa.2022.107225 ↗
11. A multi-technique and multi-scale analysis of the thermal degradation of PEEK in laser heating10.1016/j.polymdegradstab.2023.110282 ↗
12. Influence of repass treatment on carbon fibre-reinforced PEEK composites manufactured using laser-assisted automatic tape placement10.1016/j.compstruct.2020.112539 ↗
13. Detecting, characterising and assessing PEEK's and CF-PEEK’s thermal degradation in rapid high-temperature processing10.1016/j.polymdegradstab.2022.110096 ↗
14. Characterization of fiber matrix interface strength applicability of different tests, approaches and parameters10.1016/j.compscitech.2004.07.003 ↗
15. The influence of thermo-oxidative degradation on the measured interface strength of glass fibre-polypropylene10.1016/j.compositesa.2011.05.011 ↗
16. Adhesion of graphite fibers to epoxy matrices: I. The role of fiber surface treatment10.1080/00218468308074901 ↗
17. Improved interfacial adhesion in carbon fiber/poly (ether ether ketone) composites with the sulfonated poly (ether ether ketone) sizing treatment10.1002/app.51326 ↗
18. Synergy of electrochemical grafting and crosslinkable crystalline sizing agent to enhance the interfacial strength of carbon fiber/PEEK composites10.1016/j.compscitech.2020.108562 ↗
19. Strong interface construction of carbon fiber–reinforced PEEK composites: an efficient method for modifying carbon fiber with crystalline PEEK10.1002/marc.202000001 ↗
20. Interfacial enhancement of CF/PEEK composites by modifying water-based PEEK-NH$_2$ sizing agent10.1016/j.compositesb.2020.108258 ↗
21. Improving the interfacial adhesion of carbon fiber/polyether ether ketone composites by polyimide coating10.1002/slct.202001232 ↗
22. Highly enhancing the interfacial strength of CF/PEEK composites by introducing PAIK onto diazonium functionalized carbon fibers10.1016/j.apsusc.2020.145400 ↗
23. Enhanced interfacial interactions of carbon fiber reinforced PEEK composites by regulating PEI and graphene oxide complex sizing at the interface10.1016/j.compscitech.2017.11.005 ↗
24. Enhanced interfacial and mechanical properties of carbon fiber/PEEK composites by hydroxylated PEEK and carbon nanotubes10.1016/j.compositesa.2021.106364 ↗
25. Effects of multi-walled carbon nanotube/graphene oxide-based sizing on interfacial and tribological properties of continuous carbon fiber/poly(ether ether ketone) composites10.1016/j.matchemphys.2021.125344 ↗
26. Effect of preheat treatment on carbon fiber surface properties and fiber/PEEK interfacial behavior10.1002/pc.25020 ↗
27. A comparative study of the crystallinity of polyetheretherketone by using density, DSC, XRD, and Raman spectroscopy techniques10.1016/j.polymertesting.2020.106878 ↗
28. Interface strength in glass fibre–polypropylene measured using the fibre pull-out and microbond methods10.1016/j.compositesa.2009.10.005 ↗
29. Crystallinity studies of PEKK and carbon fibre/PEKK composites: a review10.1016/j.compositesb.2021.109127 ↗
30. Fracture toughness of carbon fiber/polyether ether ketone composites manufactured by autoclave and laser-assisted automated tape placement10.1002/app.41643 ↗
31. Crystallinity of on-line consolidated thermoplastic composites10.1177/002199839903300401 ↗
32. The elastic stress field arising in the single-fiber pull-out test10.1016/0266-3538(94)90027-2 ↗
33. Investigation of morphology-dependent fracture behaviour with the single-fibre pull-out test10.1016/0266-3538(93)90145-7 ↗
34. The use of a single-fibre pull-out test to investigate the influence of acidic and basic surface groups on carbon fibres on the adhesion to poly(phenylene sulfide) and matrix-morphology-dependent fracture behaviour10.1016/S0266-3538(01)00069-0 ↗
35. Investigation of the micromechanics of the microbond test10.1016/S0266-3538(97)00197-8 ↗
36. Residual stresses in thermoplastic composites—a study of the literature—Part I: formation of residual stresses10.1016/j.compositesa.2005.12.025 ↗
37. Cooling rate influences in carbon fibre/PEEK composites. Part 1. Crystallinity and interface adhesion10.1016/S1359-835X(00)00009-9 ↗
38. Effect of quenching and annealing on fiber pull-out from crystalline polymer matrices10.1163/156855191X00252 ↗
39. Fibre/matrix adhesion in thermoplastic composite: is transcrystallinity a key?
40. On transcrystallinity in semi-crystalline polymer composites10.1016/j.compscitech.2004.11.015 ↗
41. Morphological aspects of the interface in the PEEK-Carbon Fiber system10.1002/pc.750130511 ↗
42. Realizing the enhancement of interfacial interaction in semicrystalline polymer/filler composites via interfacial crystallization10.1016/j.progpolymsci.2011.12.005 ↗
43. A numerical model to prevent the thermal degradation of CFRPs at extreme heating rates – the laser processing of CF/PEEK10.1016/j.compositesa.2023.107938 ↗