Mechanical properties and slurry erosion resistance of SiC ceramic foam/epoxy co-continuous phase composite
Source abstract
Abstract
Abstract A new type of SiC ceramic foam/epoxy co-continuous phase composite (SiCfoam/EP) to be used as an anti-erosion material was prepared with the matrix of E-51 epoxy resin and the reinforcement of SiC ceramic foam in this work. Different kinds of SiC ceramic foam can greatly influence the interfacial structures and mechanical properties of composites. Among four treatments of SiC ceramic foams, it is found out that fabricating a transition layer is an efficient method to improve the mechanical properties of SiCfoam/EPs. The slurry erosion properties of SiCfoam/EP, the epoxy matrix, the pipeline steel and SiC particle reinforced epoxy-based composite (SiCp/EP) were investigated using a rotating disc rig. Owing to the supporting and shadowing effects of SiC ceramic foam, the slurry erosion resistance of SiCfoam/EP is significantly improved compared with the epoxy matrix, the pipeline steel and SiCp/EP. Therefore, SiCfoam/EP can be viewed as a promising potential application under the solid particle erosion conditions.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Erosion and Abrasive Machining · Coal Combustion and Slurry Processing · Particle Dynamics in Fluid Flows
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (27)
Show source-provided references
1. Heat transfer enhancement of an electric air heating furnace by inserting silicon carbide ceramic foam panels10.1016/j.expthermflusci.2011.12.001 ↗
2. Coupling effects of foam ceramics on the flame and shock wave of gas explosion10.1016/j.ssci.2011.08.031 ↗
3. One dimensional thermal analysis of silicon carbide ceramic foam used for solar air receiver10.1016/j.ijthermalsci.2010.08.010 ↗
4. Synergistic photocatalytic effect of TiO2 coatings and p-type semiconductive SiC foam supports for degradation of organic contaminant10.1016/j.apcatb.2013.07.016 ↗
5. Dry sliding wear behaviour of co-continuous ceramic foam/aluminium alloy interpenetrating composites produced by pressureless infiltration10.1016/j.wear.2011.12.008 ↗
6. Solid particle erosion wear characteristics of fiber and particulate filled polymer composites: a review10.1016/j.wear.2009.07.021 ↗
7. Solid particle erosion of carbon fibre- and glass fibre-epoxy composites10.1016/S0266-3538(02)00210-5 ↗
8. The solid particle erosion of polymer matrix composites10.1016/0043-1648(94)90358-1 ↗
9. Study of erosion efficiency of polymers and polymer composites10.1016/j.polymertesting.2005.10.009 ↗
10. Solid particle erosion of thermoplastic resins reinforced by short fibers10.1177/002199839402800905 ↗
11. Investigation on solid particle erosion behaviour of polyetherimide and its composites10.1016/j.wear.2006.08.012 ↗
12. Influence of impingement angle on solid particle erosion of carbon fabric reinforced polyetherimide composite10.1016/j.wear.2006.07.001 ↗
13. Solid-particle erosion of bismaleimide polymers10.1016/0043-1648(91)90126-F ↗
14. Erosion in bismaleimide polymers and bismaleimide polymer composites10.1007/BF00730858 ↗
15. Solid particle erosion of unidirectional GF reinforced EP composites with different fiber/matrix adhesion10.1177/0731684402021015779 ↗
16. Erosive wear of composite-materials10.1016/0043-1648(86)90043-8 ↗
17. Erosive wear studies of epoxy-based composites at normal incidence10.1016/j.wear.2008.03.003 ↗
18. The mechanisms of erosion of unfilled elastomers by solid particle impact10.1016/0043-1648(90)90166-8 ↗
19. Resistance of cast polyurethane elastomers to solid particle erosion10.1016/0043-1648(90)90032-6 ↗
20. Preparation and characterization of epoxy composites filled with functionalized nanosilica particles obtained via sol-gel process10.1016/S0032-3861(00)00392-X ↗
21. Schwartzwalder K, Somers AV. Method of making porous ceramic articles. US3090094, 1963-05-21.
22. Slurry erosion–corrosion behaviour of high-velocity oxy-fuel (HVOF) sprayed Fe-based amorphous metallic coatings for marine pump in sand-containing NaCl solutions10.1016/j.corsci.2011.05.062 ↗
23. Curing of epoxy matrix composites10.1177/002199838301700204 ↗
24. Investigation of impact of solid particles against hardmetal and cermet targets10.1016/S0301-679X(99)00073-0 ↗
25. Experimental analysis and modelling of particle-wall collisions10.1016/S0301-9322(99)00047-6 ↗
26. Slurry erosion resistance of fusion-bonded epoxy powder coating10.1016/S0043-1648(01)00808-0 ↗
27. Investigation of particle – wall impact process10.1016/S0043-1648(99)00175-1 ↗