Compressive Strength of Sandwich Composite Plates with Trapezoidal Cells of Different Geometries, Manufactured by Additive Manufacturing
Source abstract
Abstract
ABSTRACT In this study, the compressive strength of trapezoid composite sandwich structures with core cells made of polylactic acid filaments with three different cell widths (Dc) and cell wall thicknesses (tc) was investigated. The trapezoid composite sandwich structures were produced using a three-dimensional printer. The top and bottom surface plates were manufactured using an additive manufacturing method creating plates of composite material containing 15–20 % carbon fiber. The produced samples were assembled using epoxy adhesive. The compressive strengths of single- and double-layer sandwich composite plates were experimentally investigated. Four different parameters were identified: infill density, Dc, tc, and trapezoid base angle. The values used in fabrication for different parameters are as follows: speed (75/100/125 mm/s); infill density (70 %/85 %/100 %); Dc (6 mm/9 mm/12 mm); tc (0.8 mm/1.2 mm/1.6 mm); and finally, the trapezoid angle (55°/65°/75°). Trapezoidal cell geometries with these dimensions were used. Compression tests were performed on both single- and double-layer samples, and the Taguchi L27 experimental design was used to optimize the parameters. Signal-to-noise (S/N) ratios and analysis of variance were used for the numerical analysis of the experiments. The results of the experiments were compared based on the S/N ratios, and the parameter levels with the best results were determined. The base angle of the core cell had the largest effect on the experimental results, with a contribution of 60.46 %, followed by the base width of the core cell, which contributed 16.97 %. The lowest effect was observed for the printing speed (3.52 %) and infill rate (2.09 %). Additionally, the coefficient of determination was found to be R2 = 99.65 %.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Cellular and Composite Structures · Advanced Materials and Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Vocational School of Technical Sciences, Siirt University 1 , Siirt 56000 ,
Graduate School of Education, Department of Mechanical Engineering, Batman University 2 , Batman 72000 ,
Department of Civil Engineering, Siirt University 3 , Siirt 56000 ,
Faculty of Aeronautics and Astronautics, Kocaeli University 4 , Kocaeli 41001 ,
Faculty of Engineering and Architecture, Batman University 5 , Batman 72000 ,
References (38)
Show source-provided references
1. 3DBaskıAl, “On the History of 3D Printing Technologies,” FormBond, 2021, https://3dbaskial.com/3d-yazdirma-teknolojilerinin-tarihi-uzerine/
2. S43D, “3 Boyutlu Baskı Nedir? 3D Baskı Nasıl Yapılır?” S43D, 2025, https://s43d.com/3-boyutlu-baski-nedir-nasil-yapilir/
3. Review of Additive Manufacturing Methods10.4028/www.scientific.net/SSP.308.1 ↗
4. Mechanical Characterization and Experimental Modal Analysis of 3D Printed ABS, PC, and PC-ABS Materials10.1088/2053-1591/ab6a48 ↗
5. T. Memur, “Effect of Filament Thickness on the Mechanical Properties and Dynamic Behavior of Plates Produced by Fused Deposition Modeling (FDM) Method” (in Turkish) (master’s thesis, Bursa Uludağ University, 2023).
6. İ. K. Türkoğlu, “Investigation of the Behavior of Thermoplastic-Based Core Geometric Sandwich Structures Produced by 3D Additive Manufacturing Method under Static and Dynamic Loads” (in Turkish) (PhD diss., Bursa Uludağ University, 2020).
7. The Mechanical Behavior of a Composite Corrugated Core Coated with an Elastomer for Morphing Skins10.1177/0021998313488807 ↗
8. Advancements and Limitations in 3D Printing Materials and Technologies: A Critical Review10.3390/polym15112519 ↗
9. Manufacturing Routes for Metallic Foams10.1007/s11837-000-0062-8 ↗
10. The Resistance of Clamped Sandwich Beams to Shock Loading10.1115/1.1629109 ↗
11. Design of Adaptive Cores of Sandwich Structures Using a Compliant Unit Cell Approach and Topology Optimization10.1115/1.4002201 ↗
12. Experimental and Numerical Investigations on Laser-Welded Corrugated-Core Sandwich Panels Subjected to Air Blast Loading10.1016/j.marstruc.2014.11.007 ↗
13. Elastic Design of Syntactic Foamed Sandwiches Obtained by Filling Three-Dimensional Sandwich-Fabric Panels10.1016/S0020-7683(00)00025-1 ↗
14. Projectile Impact Testing of Glass Fiber-Reinforced Composites and Layered Corrugated Aluminum and Aluminum Foam Core Sandwich Panels: A Comparative Study10.1080/13588265.2012.690215 ↗
15. S. Kaveloğlu, “Investigation of Mechanical Properties of Honeycomb Sandwich Composites Produced with 3D Printer” (master’s thesis, Malatya İnönü University, 2024).
16. Eriyik Yığma Modelleme ile Üretilen Kafes Yapılı Parçaların Bağıl Mukavemetinin İncelenmesi [Investigation of the Relative Strength of Lattice Structured Parts Produced by Melt Masonry Modeling]10.47495/okufbed.1207865 ↗
17. Standard Test Method for Flatwise Compressive Properties of Sandwich Cores (Superseded), ASTM C365/C365M-16 (West Conshohocken, PA: ASTM International, approved May 15, 2022), https://doi.org/10.1520/C0365_C0365M-1610.1520/C0365_C0365M-16 ↗
18. Quasi-isotropic Bending Responses of Metallic Sandwich Plates with Bi-directionally Corrugated Cores10.1016/j.matdes.2010.01.009 ↗
19. Comparison of the Mechanical Properties of Samples Fabricated by Stereolithography and Fused Deposition Modeling10.55546/jmm.1358963 ↗
20. Dimensional Accuracy of Hole Diameter Produced by Material Extrusion10.1520/JTE20230378 ↗
21. Prediction Improvement of Compressive Strength and Strain of Directionally Solidified TiAl Alloy Based on Training Data Size Adjustment10.1016/j.jmrt.2024.04.165 ↗
22. Energy Consumption Prediction of Additive Manufactured Tensile Strength Parts Using Artificial Intelligence10.1089/3dp.2023.0189 ↗
23. O. Toprak, “Investigation of the Compressive Strength Properties of AIMg3/SiCp Composites” (in Turkish) (master’s thesis, Trakya University Institute of Science, 2010).
24. Dimensional Accuracy of the Acrylonitrile Butadiene Styrene Material Produced by Additive Manufacturing Method10.1007/s11665-023-08205-9 ↗
25. Raster Angle Prediction for Additive Manufacturing Process Using Machine Learning Algorithm10.3390/app14052046 ↗
26. Uniaxial Compression Testing
27. Isparta Uygulamali Bilimler Üniversitesi, “Teknoloji Fakültesi [Faculty of Technology],” Isparta Uygulamali Bilimler Üniversitesi, 2023, https://teknoloji.isparta.edu.tr/
28. An Alternative Approach to Varıance Analysis in Taguchi Method
29. S. Yıldız, “Investigation of the Mechanical Properties of Cellular Core Sandwich Structures Produced by Additive Manufacturing” (master’s thesis, Alanya Alaaddin Keykubat University, 2024).
30. On the Goodness of Four Types of Organic Fertilizers Using the Split Plot Design and the Two-Way Block Design with Interactions10.12691/ajams-5-4-4 ↗
31. Experimental Study of Optimal Self Compacting Concrete with Spent Foundry Sand as a Partial Replacement for M-Sand Using Taguchi Approach10.1515/sspjce-2016-0013 ↗
32. An Experimental Investigation on Surface Quality and Dimensional Accuracy of FDM Components
33. Fatigue Characteristics of Structural Steels in the Gigacycle Region of Loading10.1016/j.matpr.2017.06.081 ↗
34. Optimization of Nd:YAG Laser Welding Factors of Cold-Rolled Strenx 700 CR Steel by Taguchi Method10.21605/cukurovaumfd.1273719 ↗
35. An Experimental and Finite Element Analyses of 3D Printed Honeycomb Structures under Axial Compression10.1177/09673911221122333 ↗
36. 3 Boyutlu Yazıcı ile Üretilen Farklı Hücre Çaplarındaki Bal Peteği Sandviç Yapıların Eğme Dayanımlarının İncelenmesi [Investigation of the Bending Strength of Honeycomb Sandwich Structures with Different Cell Diameters Produced by 3D Printing]10.21605/cukurovaumfd.1146410 ↗
37. Fatigue Behavior of Honeycomb Sandwich Composites under Flexural and Buckling Loading
38. The Flexural and Compressive Properties of Sandwich Composites with Different 3D-Printed Core Structures10.61112/jiens.1355323 ↗