journal article·2021-11

Experimental investigation of the use of blind rivets in sandwich panels

Robert Studziński

Publisher page

Abstract

The paper presents experimental studies of the use of blind rivets (one side connection/blind connection) in sandwich panels with polyisocyanurate foam core. The laboratory pull-out tests of the rivets from the panel facing involved two types of blind rivets (with three and four clamping arms), two types of the sandwich panel facing material (steel and laminate) and an occurrence or lack of a primer layer, which is applied between the external facing and the polyisocyanurate foam during its emerging. As a result of the laboratory tests the mechanical characteristics of the varied types of the blind connections (the equilibrium load paths, the initial and the elastic stiffnesses, the elastic and the ultimate capacity, and the ductility) as well as the failure mechanisms were obtained. The provided research data was used to verify the finite element 3D model created in the Abaqus\CAE environment. This numerical model correctly predicts the results of laboratory tests in the elastic range of the mechanical response of the blind connection with steel facing.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Structural Analysis of Composite Materials · Cellular and Composite Structures · Structural Engineering and Vibration Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Institute of Building Engineering, Poznan University of Technology, Poznań, Poland

Funding

Narodowe Centrum Nauki

References (34)

Show source-provided references
1. Zenkert D. An introduction to sandwich construction. UK: Engineering Materials, Advisory Services, 1995.
2. Vinson JR, Sierakowski RL. The behavior of structures composed of composite materials . Berlin: Springer, 2006.
3. Davies JM. · 2008
4. Studziński R, Pozorski Z, Garstecki A. Failure maps of sandwich panels with soft core. In: Proceedings of the 10th international conference modern building materials, structures and techniques . 2010, pp.1060–1065. Vilnius: Vilnius Gediminas Technical University, Department of Construction Economics & Property.
5. 10.1016/j.scriptamat.2004.02.01510.1016/j.scriptamat.2004.02.015 ↗
6. Studziński R · J Theor Appl Mech · 2009 · 47 · 685
7. 10.1016/S0263-8231(99)00017-810.1016/S0263-8231(99)00017-8 ↗
8. 10.1016/j.proenv.2017.03.12110.1016/j.proenv.2017.03.121 ↗
9. 10.1016/j.applthermaleng.2012.11.01510.1016/j.applthermaleng.2012.11.015 ↗
10. Oberkofler H. Fastener for joining honeycomb panels and method for using the same. Patent No. US 6,837,659 B2, USA, 2005.
11. Spraggins MR. Method and fastener system for joining lightweight panels. Patent No. US5209805A, USA, 1992.
12. Pineiros V, Schepergerdes W. Threaded insert for receiving a threaded fastener in a composite panel. Patent No. US20080292425A1, USA, 2007.
13. ECCS (TC7 – Technical Working Group TWG 7.9, Sandwich Panels and Related Structures) and CIB (Working Commission W056, Sandwich Panels) Joint Committee. European recommendations on the stabilization of steel structures by sandwich panels. CIB Publication 379, 2014.
14. Dürr M. Die Stabilisierung biegedrillknickgefährdeter Träger durch Sandwichelemente und Trapezbleche . PhD Dissertation, Karlsruhe, 2008.10.1002/stab.200890060 ↗
15. 10.1016/j.jcsr.2017.02.01610.1016/j.jcsr.2017.02.016 ↗
16. 10.1016/j.tws.2013.09.01710.1016/j.tws.2013.09.017 ↗
17. 10.1016/j.tws.2013.10.01910.1016/j.tws.2013.10.019 ↗
18. Lawrence FW. Blind fastener for sandwich panel and method. Patent no. US 3434262 A, USA, 1967.
19. Worthing AL. Sandwich panel fastener. Patent no. US 4846612 A, USA, 1987.
20. Gauron RF. Inset panel fastener and method of using. Patent no. US 4812193 A, USA, 1989.
21. Misiek T · Proc Eurosteel · 2017 · 1 · 1746
22. 10.1016/j.acme.2018.11.00710.1016/j.acme.2018.11.007 ↗
23. Szumigała M · Eng Trans · 2018 · 66 · 161
24. 10.1617/s11527-007-9346-610.1617/s11527-007-9346-6 ↗
25. 10.1177/109963621775053910.1177/1099636217750539 ↗
26. 10.1016/j.conbuildmat.2016.05.05210.1016/j.conbuildmat.2016.05.052 ↗
27. EN ISO 6892-1:2019. Metallic materials – tensile testing – part 1: method of test at room temperature.
28. ISO 527-4:1997. Plastics – determination of tensile properties – part 4: test conditions for isotropic and orthotropic fibre-reinforced plastic composites.
29. EN 14509:2007. Self-supporting double skin metal faced insulating panels – factory made products – specifications.
30. 10.15632/jtam-pl.53.2.38310.15632/jtam-pl.53.2.383 ↗
31. 10.1098/rspa.1982.008810.1098/rspa.1982.0088 ↗
32. 10.1007/BF0264554610.1007/BF02645546 ↗
33. 10.1016/j.ijimpeng.2006.06.01210.1016/j.ijimpeng.2006.06.012 ↗
34. EN 485-2:2016. Aluminium and aluminium alloys – sheet, strip and plate – part 2: mechanical properties.