Effect of Scanning Speed on the Interface Behavior and Dendrite Growth of Laser Remelted Fe-Based Ni/WC Coatings
Source abstract
Abstract
The flame sprayed Fe-based Ni/WC cermet coating was treated by laser remelting. The influence of scanning speeds on the interface behaviour was investigated. SEM, XRD and EDS were used to analyse the microstructure, phase composition and element distribution of the interface. The results showed that the interface of the coating contained holes and interlayer cracks and showed typical mechanical bonding features. The coatings mainly consisted of [Fe, Ni], Cr, WC, Cr7C3, Fe0.04Ni0.36, and other phases. After laser remelting, the coatings were smooth and dense due to the existence of well-developed dendrite structures and metallurgical bonding and could reach the optimal performance at 200 mm/s. New phases such as Fe2Si, Cr2Si, and W2C appeared in the remelted layers. With the increase of scanning speed, the half-peak height and average grain size became wider and smaller. At the same time, the measured dendrite spacing decreased with increasing scanning speed.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Mechanical and Electrical Engineering, Jiangxi University of Science and Technology, Ganzhou 341000, China
Funding
Tribology technology and application of high end bearings -- National Open Project for local joint engineering laboratory · National Natural Science Foundation of China · Natural Science Foundation of Jiangxi province · Jiangxi Provincial Education Department
References (24)
Show source-provided references
1. Wear behavior of HVOF sprayed WC coating under water-in-oil fracturing fluid condition10.1016/j.triboint.2017.05.002 ↗
2. Comparison of microstructure and adhesion strength of plasma, flame and high velocity oxy-fuel sprayed coatings from an iron aluminide powder10.1016/j.surfcoat.2017.06.016 ↗
3. Microsliding wear behaviour of HVOF sprayed conventional and nanostructured WC–12Co coatings atelevatedtemperatures10.1179/026708410X12506870724352 ↗
4. Comparison of surface and cross-sectional micro-nano mechanical properties of flame sprayed NiCrBSi coating10.1016/j.jallcom.2016.02.118 ↗
5. Sliding wear behaviour of HVOF and HVAF sprayed Cr3C2 -based coatings10.1016/j.wear.2017.04.001 ↗
6. Effect of surface topological structure and chemical modification of flame sprayed aluminum coatings on the colonization of Cylindrotheca closterium on their surfaces10.1016/j.apsusc.2015.12.141 ↗
7. High temperature oxidation tests for the high velocity solution precursor flame sprayed manganese–cobalt oxide spinel protective coatings on SOFC interconnector steel10.1016/j.ijhydene.2015.02.129 ↗
8. Wear behaviour of flame sprayed NiCrBSi coating remelted by flame or by laser10.1016/j.wear.2006.05.009 ↗
9. Oxidation behavior of laser remelted flame sprayed NiCrAlY and NiCrAlY-Al2O3 coatings10.1016/S0257-8972(00)01102-6 ↗
10. Laser remelting of flame sprayed Al2O3 ceramic coatings and subsequent wear resistance10.1016/S0921-5093(00)00983-7 ↗
11. Interface characteristics of Al2O3-13% TiO2 ceramic coatings prepared by laser cladding10.1016/S1003-6326(11)61491-X ↗
12. Optimization of the laser remelting process for HVOF-sprayed Stellite 6 wear resistant coatings10.1016/j.optlastec.2015.09.005 ↗
13. Laser remelting of flame sprayed nanostructured Al2O3-TiO2 coatings at different laser power10.1016/j.surfcoat.2010.04.028 ↗
14. Influence and application of laser parameters on unit of H13 steel by laser remelting process10.1007/s00170-015-6812-0 ↗
15. Microstructural and corrosion behavior of Al/SiC metal matrix composites10.1016/j.asej.2014.03.003 ↗
16. Synthesis and magnetic properties of 4:1 hard-soft SrFe12O19-La1- xSrxMnO3 nanocomposite prepared by auto-combustion method10.1063/1.5096530 ↗
17. The effect of cladding speed on phase constitution and properties of AISI 431 stainless steel laser deposited coatings10.1016/j.surfcoat.2011.05.035 ↗
18. Microbeam X-ray diffraction studies of structural properties of polycrystalline metals by means of synchrotron radiation10.1016/S0921-5093(97)00839-3 ↗
19. Klug, H.P., and Alexander, L.E. (1974). X-Ray Diffraction Procedures for Polycrystalline and Amorphous Materials, Wiley-VCH. [2nd ed.].
20. Hall-Petch relations for multilayered materials10.1016/0965-9773(95)00250-I ↗
21. Three-dimensional growth morphologies in diffusion-controlled channel growth10.1103/PhysRevE.55.7789 ↗
22. Structural, magnetic, and mössbauer studies of transition metal-doped Gd2Fe16Ga0.5TM0.5 intermetallic compounds (TM = Cr, Mn, Co, Ni, Cu, and Zn)10.3390/magnetochemistry4040054 ↗
23. Role of alumina coating on Li-Ni-Co-Mn-O particles as positive electrode material for lithium-ion batteries10.1021/cm050566s ↗
24. Huang, J.H. (1996). The Diffusion in Metals and Alloys, Metallurgical Industry Press. (In Chinese).