Effect of Aluminide Coating Thickness on High-Temperature Fatigue Response of MAR-M247 Nickel-Based Superalloy
Source abstract
Abstract
In this paper, 20 µm and 40 µm thick aluminide coatings were deposited on MAR-M247 nickel-based superalloy through the chemical vapor deposition (CVD) process in a hydrogen protective atmosphere for 4 h and 12 h, respectively, at a temperature of 1040 °C and an internal pressure of 150 mbar. The effect of aluminide coating thickness on the high-temperature performance of the MAR-M247 nickel-based superalloy was examined during a fatigue test at 900 °C. After high-temperature testing, the specimens were subjected to fractographic analysis to reveal the damage mechanisms. No significant effect of coating thickness was found since the material exhibited a similar service life throughout the fatigue test when subjected to the same stress amplitude. One should stress that the coating remained well adhered after specimen fracture, confirming its effectiveness in protecting the material against high-temperature oxidation.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High Temperature Alloys and Creep · Intermetallics and Advanced Alloy Properties · High-Temperature Coating Behaviors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Institute of Fundamental Technological Research, Polish Academy of Sciences, ul. Pawińskiego 5B, 02-106 Warsaw, Poland
References (35)
Show source-provided references
1. Barwinska, I., Kopec, M., Kukla, D., Senderowski, C., and Kowalewski, Z.L. (2023). Thermal Barrier Coatings for High-Temperature Performance of Nickel-Based Superalloys: A Synthetic Review. Coatings, 13.10.3390/coatings13040769 ↗
2. Kukla, D., Kopec, M., Kowalewski, Z.L., Politis, D.J., Jóźwiak, S., and Senderowski, C. (2020). Thermal Barrier Stability and Wear Behavior of CVD Deposited Aluminide Coatings for MAR 247 Nickel Superalloy. Materials, 13.10.3390/ma13173863 ↗
3. High Cycle Fatigue of Nickel-based Superalloy MAR-M 247 at High Temperatures10.1016/j.proeng.2014.06.273 ↗
4. Kopec, M. (2024). Recent Advances in the Deposition of Aluminide Coatings on Nickel-Based Superalloys: A Synthetic Review (2019–2023). Coatings, 14.10.3390/coatings14050630 ↗
5. Effect of Aluminizing on the Fatigue and High-Temperature Corrosion Resistance of Inconel 740 Nickel Alloy10.1007/s11837-022-05662-w ↗
6. Morphology and microstructure of Yb2O3 layer formed over aluminide coating produced by pack cementation of Haynes® 263 alloy10.1007/s43452-024-00869-x ↗
7. Nourpoor, P., Javadian, S., Aghdam, A.S.R., and Ghadami, F. (2022). Microstructure Investigation and Cyclic Oxidation Resistance of Ce-Si-Modified Aluminide Coating Deposited by Pack Cementation on Inconel 738LC. Coatings, 12.10.20944/preprints202209.0081.v1 ↗
8. Low cycle fatigue and dwell-fatigue of diffusion coated superalloy Inconel 713LC at 800 °C10.1016/j.matchar.2020.110599 ↗
9. Development of a new slurry coating design for the surface protection of gas turbine components10.1016/j.surfcoat.2019.06.020 ↗
10. Oxidation behaviour of ultrafast slurry aluminized nickel10.1016/j.surfcoat.2021.127667 ↗
11. Thickness influence on creep properties for Ni-based superalloy M247LC SX10.1016/j.msea.2012.04.067 ↗
12. Effects of breakaway oxidation on local stresses in thermal barrier coatings10.1016/j.actamat.2009.10.028 ↗
13. Kedir, Y.A., and Lemu, H.G. (2023). Prediction of Fatigue Crack Initiation under Variable Amplitude Loading: Literature Review. Met, 13.10.3390/met13030487 ↗
14. Wang, P., Zhao, X., Yue, Q., Xia, W., Ding, Q., Bei, H., Gu, Y., and Zhang, Z. (2023). Crack Initiation in Ni-Based Single Crystal Superalloy under Low-Cycle Fatigue-Oxidation Conditions. Met, 13.10.3390/met13111878 ↗
15. Volkov, K. (2023). Hypersonic and Supersonic Flight-Advances in Aerodynamics, Materials, and Vehicle Design, IntechOpen.10.5772/intechopen.104045 ↗
16. Bogdan, M., and Peter, I. (2024). A Comprehensive Understanding of Thermal Barrier Coatings (TBCs): Applications, Materials, Coating Design and Failure Mechanisms. Met, 14.10.3390/met14050575 ↗
17. Effect of residual stress on the delamination response of film-substrate systems under bending10.1016/j.ijsolstr.2016.07.020 ↗
18. Solutioning and Aging of MAR-M247 Nickel-Based Superalloy10.1007/s11665-013-0565-4 ↗
19. Preparation and cyclic oxidation resistance of Hf-doped NiAl coating10.1016/j.corsci.2021.110014 ↗
20. Effect of interdiffusion on mechanical and thermal expansion properties at high temperature of a MCrAlY coated Ni-based superalloy10.1016/j.surfcoat.2016.08.059 ↗
21. Preparation and characterization of slurry aluminide coating on Super304H boiler tube in combination with heat-treatment process10.1016/j.surfcoat.2019.04.061 ↗
22. Aluminide coating formation on nickel-base superalloys by pack cementation process10.1023/A:1012534220165 ↗
23. High temperature oxidation behavior of aluminide coatings applied on HP-MA heat resistant steel using a gas-phase aluminizing process10.1016/j.surfcoat.2022.128181 ↗
24. CInfluence of thermodynamic activities of different masteralloys in pack powder mixtures to produce low activity aluminide coatings on TiAl alloys10.1016/j.intermet.2015.01.001 ↗
25. Diffusion mechanisms and microstructure development in pack aluminizing of Ni-based alloys10.1016/j.surfcoat.2013.11.034 ↗
26. Microstructural degradation and interdiffusion behavior of NiAl and Ge-modified NiAlcoatings deposited on Alloy 602 CA10.1016/j.surfcoat.2019.02.048 ↗
27. Crystal plasticity modeling of the cyclic behavior of polycrystalline aggregates under non-symmetric uniaxial loading: Global and local analyses10.1016/j.ijplas.2019.10.007 ↗
28. The analysis of strain response for as-received and exploited 10H2M power engineering steel subjected to low cycle fatigue in plastic regime10.1016/j.ijpvp.2023.105110 ↗
29. Very high cycle fatigue rupture mode at high temperatures of Ni-based superalloys coated with a slurry aluminide10.1016/j.ijfatigue.2023.108107 ↗
30. A prominent driving force for the spallation of thermal barrier coatings: Chemistry dependent phase transformation of the bond10.1016/j.actamat.2017.06.037 ↗
31. Microstructural instability in coated single crystal superalloys10.1016/j.jmatprotec.2004.04.132 ↗
32. Zhao, W., Hu, Z., Wang, L., Wang, X., Wu, Q., and Liu, R. (2023). Effect of Top-Coat Thickness and Interface Fluctuation on the Residual Stress in APS-TBCs. Coatings, 13.10.3390/coatings13091659 ↗
33. Effects of γ’ size and carbide distribution on fatigue crack growth mechanisms at 650 °C in an advanced Ni-based superalloy10.1016/j.ijfatigue.2020.106086 ↗
34. A review of underlying reasons for intergranular cracking for a variety of failure modes and materials and examples of case histories10.1016/j.engfailanal.2019.02.027 ↗
35. The role of oxidation damage in fatigue crack initiation of an advanced Ni-based superalloy10.1016/j.ijfatigue.2015.08.016 ↗