The Relationship between Coating Property and Solid Particle Erosion Resistance of AIP-Deposited TiAlN Coatings with Different Al Contents
Source abstract
Abstract
TiAlN coatings with different Al ratios were deposited by the cathodic arc ion plating (AIP) method, and the relationship between solid particle erosion resistance and structural, mechanical properties was investigated by a micro slurry-jet erosion (MSE) test. The crystal structure of TiAlN coating changes depending on the Al ratio. The coating shows a B1 single cubic phase between the Al ratio of 0 and 0.58; above this ratio, formation of a B4 hexagonal phase is observed. The mechanical properties such as hardness and Young’s modulus of the TiAlN coating also depend on the Al ratio and the crystal structure. The erosion rate decreases by increasing the Al ratio up to 0.58, as the coating is a cubic single phase. The TiAlN coating shows the lowest erosion rate at an Al ratio of 0.58. The erosion rate increases drastically as the crystalline phase changes from the B1 cubic to B4 hexagonal phase at the Al ratio of more than 0.58. The change in erosion rate is also discussed in connection with mechanical properties such as erodent particle hardness to coating hardness ratio and coating hardness to Young’s modulus ratio.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Metal and Thin Film Mechanics · High-Temperature Coating Behaviors · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Applied Physics Research Laboratory, Kobe Steel Ltd., 1-5-5 Takatuskadai Nishiku, Kobe 651-2271, Hyogo, Japan
Fukui Tecco Co., Ltd., Fukui 910-0831, Japan
Department of Mechanical Engineering, University of Fukui, Fukui 910-8507, Japan
References (31)
Show source-provided references
1. Turbine blade surface deterioration by erosion10.1115/1.1860376 ↗
2. Protective coatings in the gas turbine engine
3. Yang, L., Nakatani, Y., Yamada, M., Abe, T., Kitaguchi, K., Ono, Y., Yamamoto, K., and Munemasa, J. (2017, January 26–30). Evaluation and application of hard coatings for steam turbine. Proceedings of the ASME 2017 Power Conference Joint With ICOPE-17, Charlotte, NC, USA.
4. Erosion of hard material coating systems10.1016/0043-1648(88)90209-8 ↗
5. Solid particle erosion resistance of hard chemically vapour deposited coatings10.1016/0257-8972(89)90113-8 ↗
6. High energy solid particle erosion mechanisms of superhard CVD coatings10.1016/j.wear.2005.02.043 ↗
7. Effect of crystallographic orientation on erosion characteristics of arc evaporation titanium nitride coating10.1016/0257-8972(87)90186-1 ↗
8. Influence of residual compressive stress on erosion behavior of arc evaporation titanium nitride coating10.1016/0257-8972(88)90010-2 ↗
9. Wear of PVD Ti/TiN multilayer coatings10.1016/S0257-8972(96)03141-6 ↗
10. High thickness Ti/TiN multilayer thin coatings for wear resistant applications10.1016/j.surfcoat.2006.03.042 ↗
11. Ti–N multilayer systems for compressor airfoil sand erosion protection10.1016/j.surfcoat.2009.09.053 ↗
12. Nanolayered multilayer Ti/TiN coatings: Role of bi-layer thickness and annealing on solid particle erosion behaviour at elevated temperature10.1016/j.surfcoat.2018.10.007 ↗
13. Ikeda, T., and Sato, H. (, 1990). Properties of hard coating in the TiAlN system prepared by the cathodic arc ion plating method. Presented at the 5th International Symposium of the Japan Welding Society 5JWs-II-20, Osaka, Japan.
14. Titanium aluminum nitride films: A new alternative to TiN coatings10.1116/1.573713 ↗
15. Erosion wear of CrN, TiN, CrAlN, and TiAlN PVD nitride coatings10.1016/j.ijrmhm.2012.03.002 ↗
16. Nanolayered CrAlTiN and multilayered CrAlTiN–AlTiN coatings for solid particle erosion protection10.1016/j.triboint.2014.11.002 ↗
17. Erosion resistance performance of magnetron sputtering deposited TiAlN coatings10.1016/j.surfcoat.2004.08.012 ↗
18. Sand erosion resistance improvement and damage mechanism of TiAlN coating via the bias-graded voltage in FCVA deposition10.1016/j.surfcoat.2019.125009 ↗
19. Barshilia Solid particle erosion and corrosion resistance performance of nanolayered multilayered Ti/TiN and TiAl/TiAlN coatings deposited on Ti6Al4V substrates10.1016/j.surfcoat.2020.125531 ↗
20. Properties of (Ti,Cr,Al)N coatings with high Al content deposited by new plasma enhanced arc-cathode10.1016/S0257-8972(03)00580-2 ↗
21. Yamamoto, K., Abdoos, M., Paiva, J.M., Stolf, P., Beake, B., Rawal, S., Fox-Rabinovich, G., and Veldhuis, S. (2018). Cutting performance of low stress thick TiAlN PVD coatings during machining of compacted graphite cast iron (CGI). Coatings, 8.10.3390/coatings8010038 ↗
22. Accurate absolute peak positions for multiple {hkl} residual stress analysis by means of misalignment corrections10.1524/zksu.2006.suppl_23.49 ↗
23. Young’s modulus and stress of CrN deposited by cathodic vacuum arc evaporation10.1016/0257-8972(94)90149-X ↗
24. Simplified method for analyzing nanoindentation data and evaluating performance of nanoindentation instruments10.1557/JMR.2001.0426 ↗
25. Evaluation of wear resistance of thin hard coatings by a new solid particle impact test10.1016/S0043-1648(01)00743-8 ↗
26. Evaluation of erosive wear resistance of TiN coatings by a slurry jet impact test10.1016/j.wear.2005.09.030 ↗
27. Development of a new type micro slurry-jet erosion (MSE) tester for evaluation of wear properties of hard thin coatings10.1002/ls.81 ↗
28. Effects of hardness and fracture toughness of target materials and impact particles on erosion of ceramic materials10.4028/www.scientific.net/KEM.71.51 ↗
29. Solid particle erosion mechanisms of hard protective coatings10.1016/j.surfcoat.2013.07.050 ↗
30. Solid particle erosion mechanisms of protective coatings for aerospace applications10.1016/j.surfcoat.2014.08.037 ↗
31. Evaluation of coating properties with a Micro Slurry-jet Erosion (MSE) test—Effects of the shape and size of erodent particles on erosion behaviors of TiN coating10.1016/j.surfcoat.2021.127443 ↗