Abrasive Wear Resistance and Tribological Characteristics of Pulsed Hard Anodized Layers on Aluminum Alloy 1011 in Tribocontact with Steel and Ceramics in Various Lubricants
Source abstract
Abstract
Based on the analysis of known methods of surface hardening of aluminum alloys (chromium plating, plasma electrolytic oxidation, hard anodizing), the prospects for pulsed hard anodizing are shown both for improving the functional characteristics of alloys and for large-scale implementation of this method. The purpose of this work is to show the possibility of pulsed hard anodizing to improve the serviceability of low-strength aluminum alloy 1011 under conditions of abrasive and sliding wear. The influence of the pulsed anodizing temperature on the phase-structural state of the synthesized layers, their abrasive wear resistance, and tribological characteristics in various lubricants were established, and the mechanism of wear of these layers was proposed. It is shown that with an increase in the temperature of pulsed anodizing, the wear resistance of the synthesized layers increases, and their abrasive wear resistance decreases. The negative effect of lubricating media on the wear resistance of the synthesized layers compared to tests under dry conditions was shown, and an explanation for this phenomenon is proposed. A significant (up to 40 times) increase in wear resistance in dry friction of anodized low-strength aluminum alloy 1011 compared to high-strength aluminum alloy 1050 was shown.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced materials and composites · Anodic Oxide Films and Nanostructures · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Karpenko Physico-Mechanical Institute of the National Academy of Sciences of Ukraine, 5, Naukova Str., 79060 Lviv, Ukraine
Department of Mechanical Energy and Biotechnology Engineering, Vytautas Magnus University, Akademija, LT-53361 Kaunas, Lithuania
Funding
Department of Physical and Technical Problems of Materials Science of the National Academy of Sciences
References (68)
Show source-provided references
1. Peltier, F., and Thierry, D. (2022). Review of Cr-free coatings for the corrosion protection of aluminum aerospace alloys. Coatings, 12.10.3390/coatings12040518 ↗
2. Physico-chemical characterisation and tribological behaviour of micro-arc oxidation coating on aluminium alloy—Comparison with hard anodised oxidation10.1016/j.wear.2022.204591 ↗
3. Cored-wire arc spray fabrication of novel aluminium-copper coatings for anti-corrosion/fouling hybrid performances10.1016/j.surfcoat.2018.10.094 ↗
4. Improvement of wear resistance of aluminum alloy by HVOF method10.1016/j.jmrt.2020.11.102 ↗
5. Student, M., Hvozdetskyi, V., Stupnytskyi, T., Student, O., Maruschak, P., Prentkovskis, O., and Skačkauskas, P. (2022). Mechanical properties of arc coatings sprayed with cored wires with different charge compositions. Coatings, 12.10.3390/coatings12070925 ↗
6. Peng, Z., Xu, H., Liu, S., Qi, Y., and Liang, J. (2021). Wear and corrosion resistance of plasma electrolytic oxidation coatings on 6061 Al alloy in electrolytes with aluminate and phosphate. Materials, 14.10.3390/ma14144037 ↗
7. Plasma electrolytic oxidation coatings on aluminum alloys: Microstructures, properties, and applications
8. Liu, W., Pu, Y., Liao, H., Lin, Y., and He, W. (2020). Corrosion and wear behavior of PEO coatings on D16T aluminum alloy with different concentrations of graphene. Coatings, 10.10.3390/coatings10030249 ↗
9. Student, M., Pohrelyuk, I., Padgurskas, J., Posuvailo, V., Hvozdets’kyi, V., Zadorozhna, K., Chumalo, H., Veselivska, H., Kovalchuk, I., and Kychma, A. (2023). Influence of plasma electrolytic oxidation of cast Al-Si alloys on their phase composition and abrasive wear resistance. Coatings, 13.10.3390/coatings13030637 ↗
10. Sieber, M., Simchen, F., Morgenstern, R., Scharf, I., and Lampke, T. (2018). Plasma electrolytic oxidation of high-strength aluminium alloys—Substrate effect on wear and corrosion performance. Metals, 8.10.3390/met8050356 ↗
11. Anodizing Al–Si foundry alloys: A critical review10.1002/adem.202101480 ↗
12. Hard anodizing of aerospace AA7075-T6 aluminum alloy for improving surface properties10.1007/s12666-019-01754-5 ↗
13. Tribological properties of the oxide coatings produced onto 6061-T6 aluminum alloy in the hard anodizing process10.1007/s11665-018-3421-8 ↗
14. Bazaluk, O., Dubei, O., Ropyak, L., Shovkoplias, M., Pryhorovska, T., and Lozynskyi, V. (2022). Strategy of compatible use of jet and plunger pump with chrome parts in oil well. Energies, 15.10.3390/en15010083 ↗
15. Development of Analytical Model of Threaded Connection of Tubular Parts of Chrome-Plated Metal Structures10.15407/mfint.44.02.0251 ↗
16. Simchen, F., Sieber, M., Kopp, A., and Lampke, T. (2020). Introduction to Plasma Electrolytic Oxidation—An Overview of the Process and Applications. Coatings, 10.10.3390/coatings10070628 ↗
17. Sikdar, S., Menezes, P.V., Maccione, R., Jacob, T., and Menezes, P.L. (2021). Plasma Electrolytic Oxidation (PEO) Process—Processing, Properties, and Applications. Nanomaterials, 11.10.3390/nano11061375 ↗
18. Analytical study of “crosshead–slide rail” wear effect on pump rod stress state10.1088/1742-6596/1741/1/012039 ↗
19. Structure and mechanical properties of ceramic coatings fabricated by plasma electrolytic oxidation on aluminized steel10.1016/j.apsusc.2007.04.007 ↗
20. Plasma electrolytic oxidation of arc sprayed aluminium coatings [Plasmaelektrolytische Oxidation Thermisch Gespritzter Aluminiumschichten]10.1002/mawe.200800407 ↗
21. Design of a two-layer Al–Al2O3 coating with an oxide layer formed by the plasma electrolytic oxidation of Al for the corrosion and wear protections of steel
22. Characterization and mechanical properties of the duplex coatings produced on steel by electro-spark deposition and micro-arc oxidation10.1016/j.surfcoat.2013.10.004 ↗
23. Yang, Z., Guo, X., Lu, S., Zhang, Y., Hu, H., Lu, K., and Zhang, J. (2021). Investigation of Stray Radiation Suppression in Infrared Imaging System Using a Novel Broadband and High-Absorption Ceramic Coating. Appl. Sci., 11.10.3390/app11114952 ↗
24. Bembenek, M., Makoviichuk, M., Shatskyi, I., Ropyak, L., Pritula, I., Gryn, L., and Belyakovskyi, V. (2022). Optical and Mechanical Properties of Layered Infrared Interference Filters. Sensors, 22.10.3390/s22218105 ↗
25. The properties of oxide-ceramic layers with Cu and Ni inclusions synthesizing by PEO method on top of the gas-spraying coatings on aluminium alloys10.1016/j.vacuum.2020.109514 ↗
26. Moshrefifar, M., Ebrahimifar, H., and Hakimizad, A. (2022). Systematic investigation of silicon content effects on the PEO coatings’ properties on Al–Si binary alloys in silicate-based and tungstate-containing electrolytes. Coatings, 12.10.3390/coatings12101438 ↗
27. Friction behavior of iron-carbon alloys in couples with plasma-electrolytic oxide-ceramic layers synthesized on D16T alloy10.1007/s11003-017-0083-x ↗
28. Plasma electrolytic oxidation coatings with particle additions—A review10.1016/j.surfcoat.2016.08.055 ↗
29. Characterization and tribological properties of hard anodized and micro arc oxidized 5754 quality aluminum alloy
30. Characteristics and tribological behavior of the hard anodized 6061-T6 Al alloy10.1016/j.jallcom.2020.155988 ↗
31. Gold hard anodized (GHA) materials with antimicrobial surface properties: Mechanical, tribological, and microbiological characterization10.1007/s42247-021-00180-y ↗
32. Musza, A., Windisch, M., Török, M., Molnár, T., Kovács, S., Sátán-Papp, S., Szegedi, K., Ugi, D., Chinh, N.Q., and Vida, Á. (2023). Tribological examination of anodized Al-356 for automotive use. Coatings, 13.10.3390/coatings13091642 ↗
33. Modification of the surfaces of aluminum and titanium alloys aimed at the improvement of their wear resistance and tribological characteristics10.1007/s11003-021-00552-z ↗
34. Influence of the composition of electrolyte for hard anodizing of aluminum on the characteristics of oxide layer10.1007/s11003-021-00538-x ↗
35. Effects of anodizing conditions and the addition of Al2O3/PTFE particles on the microstructure and the mechanical properties of porous anodic coatings on the AA1050 aluminium alloy10.1016/j.apsusc.2020.145780 ↗
36. Martínez-Viademonte, M.P., Abrahami, S.T., Hack, T., Burchardt, M., and Terryn, H. (2020). A review on anodizing of aerospace aluminum alloys for corrosion protection. Coatings, 10.10.3390/coatings10111106 ↗
37. Improvement of the functional characteristics of coatings obtained by the method of hard anodizing of aluminum alloys10.1007/s11003-021-00500-x ↗
38. Why it makes sense to upgrade to pulse anodizing: Mock finishing shop scenarios show how switching from conventional anodizing processes to newer methods can boost productivity while maximizing ROI10.1016/S0026-0576(09)80201-8 ↗
39. Pulse anodizing—An overview
40. Mechanical properties of a pulsed anodised 5005 aluminium alloy10.1016/j.surfcoat.2019.125233 ↗
41. Modification of nanostructured anodized aluminum coatings by pulse current mode10.1016/j.surfcoat.2015.08.004 ↗
42. High-voltage electrochemical oxidation of an aluminum alloy with preliminary electrolytic-plasma surface treatment
43. Pulsed current effect on hard anodizing process of 7075-T6 aluminium alloy10.1016/j.surfcoat.2015.03.010 ↗
44. Optimization of anodic layer properties on aluminium in mixed oxalic/sulphuric acid bath using statistical experimental methods10.1016/j.surfcoat.2007.03.027 ↗
45. Study of anodic oxidation of aluminum in mixed acid using a pulsed current10.1016/S0257-8972(99)00646-5 ↗
46. Hard anodisation of aluminium and its application to sensorics10.1179/174329405X50000 ↗
47. Improved corrosion protection properties in anodic films type porous on 2024 T3 aluminium alloys obtained by pulse reverse plating10.1016/S1452-3981(23)12997-X ↗
48. Formation mechanism of pulse current anodized film on AZ91D Mg alloy10.1016/S1003-6326(08)60004-7 ↗
49. Effect of high frequencypulsing on the interfacial structure of anodized Aluminium—TiO210.1149/2.0311507jes ↗
50. High frequency pulse anodising of magnetron sputtered Al-Zr and Al-Ti coatings10.1016/j.matdes.2016.01.091 ↗
51. High frequency anodising of aluminium—TiO2 surface composites: Anodising behaviour and optical appearance10.1016/j.surfcoat.2015.07.035 ↗
52. AlSi(Cu) anodic oxide layers formed in H2SO4 at low temperature using different current waveforms10.1016/S0257-8972(02)00733-8 ↗
53. Pulsed current effect on hard anodizing process of 2024-T3 aluminium alloy10.1016/j.surfcoat.2016.01.056 ↗
54. Structural engineering of nanoporous anodic aluminium oxide by pulse anodization of aluminium10.1038/nnano.2008.54 ↗
55. The behaviour of second phase particles during anodizing of aluminium alloys10.1016/j.corsci.2010.03.029 ↗
56. Preferential anodic oxidation of second-phase constituents during anodising of AA2024-T3 and AA7075-T6 alloys10.1002/sia.3191 ↗
57. Raffin, F., Echouard, J., and Volovitch, P. (2023). Influence of the anodizing time on the microstructure and immersion stability of tartaric-sulfuric acid anodized aluminum alloys. Metals, 13.10.3390/met13050993 ↗
58. Mechanisms of hydrogen absorption, trapping and release during galvanostatic anodization of high-strength aluminum alloys10.1016/j.jmrt.2022.11.111 ↗
59. Student, M., Pohrelyuk, I., Padgurskas, J., Hvozdets’kyi, V., Zadorozna, K., Chumalo, H., Student, O., and Kovalchuk, I. (2023). The effect of heat treatment on the structural-phase state and abrasive wear resistance of a hard-anodized layer on aluminum alloy 1011. Coatings, 13.10.3390/coatings13020391 ↗
60. The effect of removing worn particles by ultrasonic cleaning on the wear characterization of LM13 alloy10.3103/S1068375515040067 ↗
61. DOE application for anslysis of tribological properties of the Al2O3/IF-WS2 surface layers10.1515/eng-2021-0012 ↗
62. Chen, L., Liu, Z., Wang, B., Song, Q., Wan, Y., and Chen, L. (2019). Surface characterization and tribological performance of anodizing micro-textured aluminum-silicon alloys. Materials, 12.10.3390/ma12111862 ↗
63. Mechanical and tribological properties of anodic Al coatings as a function of anodizing conditions. Surf. Coat
64. The Crystal Structure of Boehmite10.1346/CCMN.1979.0270201 ↗
65. Refinement of the crystal structure of gibbsite, Al(OH)310.1524/zkri.1974.139.1-2.129 ↗
66. Experimental investigation on tribological behavior of hard anodized aluminum Tauseef
67. Soffritti, C., Fortini, A., Nastruzzi, A., Sola, R., Merlin, M., and Garagnani, G.L. (2021). Dry sliding behavior of an aluminum alloy after innovative hard anodizing treatment. Materials, 14.10.3390/ma14123281 ↗
68. Santecchia, E., Cabibbo, M., Magid, A., Hamouda, S., Musharavati, F., Popelka, A., and Spigarelli, S. (2020). Dry sliding tribological properties of a hard anodized AA6082 aluminum alloy. Metals, 10.10.3390/met10020207 ↗