Influence of Different Contact Conditions on Friction Properties of AISI 430 Steel Sheet with Deep Drawing Quality
Source abstract
Abstract
This article aims to investigate the influence of different contact conditions on the friction properties of an Nb-stabilized AISI 430 ferritic stainless-steel sheet with deep drawing quality. Three tribological tests were performed: pin-on-disk, bending under tension, and strip-tension test. Moreover, counter samples of a hard metal (WC-12%Co) with surface finishes of 0.27 and 0.54 μm were used in the friction tests under dry and lubricated conditions. The influence of the texture and relative elongation of the strip on formability also were investigated. A comparative analysis of the results revealed that the coefficients of friction, wear, lubricant efficiency, and hardness measured below the wear surface indicated a strong dependence on surface roughness and the friction test type. The coefficients of friction obtained from the pin-on-disk test were higher than those obtained from the formability tests. In addition, the coefficient of friction increased with increasing relative elongation during the formability tests; it was higher in the bending-under-tension test than in the strip-tension test, mainly owing to the increasing strip surface roughness. The contact pressure during the formability tests was non-uniform during strip sliding under the tool. According to our results, for each friction condition in a specific area of the forming die, there is a value of the coefficient of friction, depending on the kinematic conditions. Therefore, the results can be used as input data to define design guidelines, improve productivity, and improve product quality from this steel sheet.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Mechanical stress and fatigue analysis · Metal Alloys Wear and Properties · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Graduate Program in Mechanical Engineering, Universidade Federal de Minas Gerais, Av. Antônio Carlos, 6627, Pampulha, Belo Horizonte 31270-901, MG, Brazil
Department of Metallurgy and Chemistry, Centro Federal de Educação Tecnológica de Minas Gerais, R. 19 de Novembro, 121, Centro Norte, Timóteo 35180-008, MG, Brazil
References (48)
Show source-provided references
1. Influence of geometric attributes on friction coefficient in sheet metal stamping10.5194/ms-12-945-2021 ↗
2. Azushima, A. (2022). Tribological Technology in Sheet Metal Forming. Materials Forming, Machining and Tribology, Springer. [1st ed.].10.1007/978-981-16-6230-0 ↗
3. Influence of tribology on global energy consumption, costs and emissions10.1007/s40544-017-0183-5 ↗
4. Trzepiecinski, T., and Lemu, H.G. (2020). Recent Developments and Trends in the Friction Testing for Conventional Sheet Metal Forming and Incremental Sheet Forming. Metals, 10.10.3390/met10010047 ↗
5. An investigation on the friction in a micro sheet metal roll forming processes considering adhesion and ploughing10.1016/j.jmatprotec.2020.116790 ↗
6. Influência da velocidade de estampagem e anisotropia no comportamento tribológico e fratura de uma chapa de aço AISI 430Nb
7. Trzepiecinski, T., and Lemu, H. (2020). Effect of Lubrication on Friction in Bending under Tension Test-Experimental and Numerical Approach. Metals, 10.10.3390/met10040544 ↗
8. Effect of the test conditions on tribological behavior of an Nb-stabilized AISI 430 stainless steel sheet10.1007/s40430-021-03235-7 ↗
9. Baltatu, M.S., Vizureanu, P., Sandu, A.V., Munteanu, C., and Istrate, B. (2020). Microstructural Analysis and Tribological Behavior of Ti-Based Alloys with a Ceramic Layer Using the Thermal Spray Method. Coatings, 10.10.3390/coatings10121216 ↗
10. Paleu, C.C., Munteanu, C., Istrate, B., Bhaumik, S., Vizureanu, P., Bălţatu, M.S., and Paleu, V. (2020). Microstructural Analysis and Tribological Behavior ofAMDRY 1371 (Mo–NiCrFeBSiC) Atmospheric Plasma Spray Deposited Thin Coatings. Coatings, 10.10.3390/coatings10121186 ↗
11. Staeves, J. (1998). Beurteilung der Topografie von Blechen im Hinblick auf die Reibung bei der Umformung. [Ph.D. Thesis, Technical University of Darmstadt].
12. Daehn, G., Cao, J., Kinsey, B., Tekkaya, E., Vivek, A., and Yoshida, Y. (2021). Forming the Future, Proceedings of the 13th International Conference on the Technology of Plasticity, Columbus, OH, USA, 25–30 July 2021, Springer. The Minerals, Metals & Materials Series.10.1007/978-3-030-75381-8 ↗
13. Kharrat, M., Baccar, M., and Dammak, F. (2021). Advances in Mechanical Engineering, Materials and Mechanics, Proceedings of the ICAMEM 2019, Hammamet, Tunisia, 16–18 December 2019, Springer. Lecture Notes in Mechanical Engineering.10.1007/978-3-030-52071-7 ↗
14. Trzepieciński, T. (2019). A study of the coefficient of friction in steel sheets forming. Metals, 9.10.3390/met9090988 ↗
15. Design of a tribo-simulator for investigation of the tribological behavior of stainless-steel sheets under different contact conditions10.1590/1980-5373-mr-2021-0220 ↗
16. Trzepieciński, T., and Najm, S.M. (2022). Application of artificial neural networks to the analysis of friction behaviour in a drawbead profile in sheet metal forming. Materials, 15.10.3390/ma15249022 ↗
17. Trzepieciński, T. (2022). Polynomial multiple regression analysis of the lubrication effectiveness of deep drawing quality steel sheets by eco-friendly vegetable oils. Materials, 15.10.3390/ma15031151 ↗
18. Lubricant test methods for sheet metal forming10.1016/j.triboint.2007.11.017 ↗
19. The difficulty of measuring low friction: Uncertainty analysis for friction coefficient measurements10.1115/1.1843853 ↗
20. Codd, D.S. (2011). Automotive Mass Reduction with Martensitic Stainless Steel, SAE International. SAE Technical Paper 2011-01-0427.10.4271/2011-01-0427 ↗
21. A new class of lightweight, stainless steels with ultra-high strength and large ductility10.1038/s41598-020-69177-7 ↗
22. Failure analysis of AISI 430 stainless steel sheet under stretching and bending conditions10.1007/s00170-022-09451-2 ↗
23. Passive films on stainless steels—Chemistry, structure and growth10.1016/S0013-4686(02)00841-1 ↗
24. Low-density steels: Complex metallurgy for automotive applications10.1007/s11837-014-1084-y ↗
25. Current state of Fe–Al–Mn–C low density steels10.1016/j.pmatsci.2017.05.002 ↗
26. The influence of tool steel microstructure on friction in sheet metal forming10.1016/j.wear.2013.01.050 ↗
27. ISSF (2022, November 30). The Ferritic Solution: Properties, Advantages, Applications. Available online: https://www.worldstainless.org/Files/issf/non-image-files/PDF/ISSF_The_Ferritic_Solution_English.pdf.
28. Microstructural characterization and mechanical behavior during recrystallization annealing of Nb-stabilized type ASTM 430 and Nb-Ti-stabilized ASTM 439 ferritic stainless steels10.1016/j.jmrt.2019.07.015 ↗
29. (2012). Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications (Standard No. ASTM A240:2012).
30. (2020). Specifies the Method for Tensile Testing of Metallic Materials and Defines the Mechanical Properties Which Can Be Determined at Room Temperature (Standard No. EN ISO 6892-1:2020).
31. Banabic, D., Bunge, H.-J., Pöhlandt, K., and Tekkaya, A.E. (2000). Springer.
32. (2016). Standard Test Methods for Tension Testing of Metallic Materials (Standard No. ASTM E8:2016).
33. Rabinowicz, E. (1995). Friction and Wear of Materials, John Wiley & Sons Ltd.. [2nd ed.].
34. Contact and Rubbing of Flat Surfaces10.1063/1.1721448 ↗
35. (2010). Standard Test Method for Wear Testing with a Pin on Disk Apparatus (Standard No. ASTM G99-05:2010).
36. Bending under tension test with direct friction measurement10.1243/095440505X32913 ↗
37. Hutchings, I.M., and Shipway, P. (2017). Tribology: Friction and Wear of Engineering Materials, Butterworth-Heinemann. [2nd ed.].10.1016/B978-0-08-100910-9.00003-9 ↗
38. Bhushan, B. (2013). Introduction to Tribology, John Wiley & Sons Ltd.. [2nd ed.].10.1002/9781118403259 ↗
39. Holmberg, K., and Matthews, A. (2009). Coatings Tribology: Properties, Mechanisms, Techniques and Applications in Surface Engineering, Elsevier Sciense. [2nd ed.].
40. Delamination of near-surface layer on cold rolled AlFeSi alloy during sheet forming10.1016/j.matchar.2014.11.011 ↗
41. The delamination theory of wear10.1016/0043-1648(73)90125-7 ↗
42. Tribology in Metalworking: Friction, Lubrication, and Wear10.1007/BF02833697 ↗
43. Friction behaviour in strip draw test of pre-stretched high strength automotive aluminium alloys10.1016/j.ijmachtools.2013.05.002 ↗
44. An analysis of ridging of ferritic stainless steel 43010.1016/j.msea.2017.01.021 ↗
45. The effect of texture on ridging of ferritic stainless steel10.1016/S1359-6454(03)00187-3 ↗
46. Frictional characteristics of steel sheets used in automotive industry10.1007/s12239-015-0087-1 ↗
47. Ter Haar, R. (1996). Friction in Sheet Metal Forming, the Influence of (Local) Contact Conditions and Deformation. [Ph.D. Thesis, Universiteit Twente].
48. The effect of niobium and homogenization on the wear resistance and some mechanical properties of ferritic stainless steel containing 17–18 wt.% chromium10.1016/S0924-0136(98)00446-4 ↗