Effect of Pulsed-Plasma Treatment on the Structural-Phase Composition and Tribological Properties of Detonation Coatings Based on Ti–Si–C
Source abstract
Abstract
The structural-phase state and tribological characteristics of detonation coatings based on Ti–Si–C before and after pulsed-plasma exposure have been experimentally investigated. The authors of the research used a detonation set-up of CCDS2000 to obtain coatings. The modification of coating surfaces was carried out by a pulsed-plasma flow using the “Impulse-6” installation. The results of the research have shown that the modification of coatings surface by a pulsed-plasma effect causes an increase in the microhardness of the surface layer and in its wear resistance. It was determined that after such type of treatment, there is an increase in the content of the Ti3SiC2 phase. According to the results of XRD analysis, the improvement in the mechano-tribological properties of detonation spraying coatings of the Ti–Si–C system as a result of pulsed-plasma treatment is associated with an increase in the content of Ti3SiC2 phases in the coatings, as well as the formation of carbide and oxide phases on the surface layer.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: MXene and MAX Phase Materials · Advanced materials and composites · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Research Center “Surface Engineering and Tribology”, Sarsen Amanzholov East Kazakhstan University, Ust-Kamenogorsk 070000, Kazakhstan
PlasmaScience LLP, Ust-Kamenogorsk 070010, Kazakhstan
School of Metallurgy and Mineral Processing, Daulet Serikbaev East Kazakhstan Technical University, Ust-Kamenogorsk 070002, Kazakhstan
Department of Physics, South Kazakhstan State Pedagogical University, Shymkent 160005, Kazakhstan
Institute for Composite Materials, Ust-Kamenogorsk 070010, Kazakhstan
References (23)
Show source-provided references
1. Kuchumova, I.D., Batraev, I.S., Ulianitsky, V.Y., Shtertser, A.A., Gerasimov, K.B., Ukhina, A.V., Bulina, N.V., Bataev, I.A., Koga, G.Y., and Guo, Y. (2019). Formation of Metallic Glass Coatings by Detonation Spraying of a Fe66Cr10Nb5B19 Powder. Metals, 9.10.3390/met9080846 ↗
2. Enhancing the properties of WC/ Co detonation coatings using two-component fuels10.1016/j.surfcoat.2016.08.008 ↗
3. Samodurova, M., Shaburova, N., Samoilova, O., Moghaddam, A.O., Pashkeev, K., Ul’yanitckiy, V., and Trofimov, E. (2021). Properties of WC–10%Co–4%Cr Detonation Spray Coating Deposited on the Al–4%Cu–1%Mg Alloy. Materials, 14.10.3390/ma14051206 ↗
4. Sun, Z., Zhu, S., Dong, W., Ding, H., Bai, Y., Luo, Y., and Di, P. (2021). Geometric Influence of Hard Phase on Corrosion Performance between WC-Reinforced Coatings Prepared by High-Velocity Oxygen-Fuel Spray and Electric Contact Strengthening. Coatings, 11.10.3390/coatings11060694 ↗
5. The Mn+1AXn: A new Class of Solids: Thermodynamically Stable Nanolaminates10.1016/S0079-6786(00)00006-6 ↗
6. Shi, Q., Zhu, H., and Li, C. (2020). The Effects of the Addition of Ti3SiC2 on the Microstructure and Properties of Laser Cladding Composite Coatings. Coatings, 10.10.3390/coatings10050498 ↗
7. Unraveling the mechanical and tribological properties of a novel Ti5Si3/TiC nanocomposite coating synthesized by a double glow discharge plasma technique10.1016/j.ceramint.2013.05.065 ↗
8. Spark Plasma Sintering and tribological behavior of Ti3SiC2-Ti5Si3-TiC composites10.1016/j.ceramint.2019.07.181 ↗
9. Rakhadilov, B.K., Buitkenov, D.B., Tuyakbaev, B.T., Sagdoldina, Z.B., and Kenesbekov, A.B. (2019). Structure and properties of detonation coatings based on titanium carbosilicide. Key Engineering Materials, Trans Tech Publications Ltd.10.4028/www.scientific.net/KEM.821.301 ↗
10. Evaluation of properties of spark plasma sintered Ti3SiC2 and Ti3SiC2/SiC composites10.1016/j.ceramint.2019.03.144 ↗
11. Impact of the detonation gas spraying mode on the phase composition and adhesional strength of Ti–Si–C coatings
12. Fabrication and characterization of micro-laminated TiC-Ti5Si3-Ti3SiC2 composite coatings by atmosphere plasma spraying10.1016/j.vacuum.2018.12.014 ↗
13. Influence of Heat Treatment on the Phase Composition and Microhardness of Coatings Based on Ti3SiC2/TiC10.4028/www.scientific.net/KEM.839.137 ↗
14. Reserach of the mechanic-tribological characteristics of Ti3SiC2/TiC coatings after annealing10.29317/ejpfm.2020040109 ↗
15. Rakhadilov, B., Buitkenov, D., Sagdoldina, Z., Seitov, B., Kurbanbekov, S., and Adilkanova, M. (2021). Structural Features and Tribological Properties of Detonation Gun Sprayed Ti–Si–C Coating. Coatings, 11.10.3390/coatings11020141 ↗
16. High-Speed Plasma Jet Modification and Doping of α-Fe10.1134/1.1398947 ↗
17. Impul’sno-plazmennoye uprochneniye instrumenta
18. Plasma-detonation technology for modification of the surface layer of metal parts10.2174/1876531900901010013 ↗
19. Computer-controlled detonation spraying: From process fundamentals toward advanced applications10.1007/s11666-011-9649-6 ↗
20. Detonation spraying behaviour of refractory metals: Case studies for Mo and Ta-based powders10.1016/j.apt.2018.04.023 ↗
21. Structure and composition of Fe-Co-Ni and Fe-Co-Ni-Cu coatings obtained by detonation spraying of powder mixtures10.1016/j.matlet.2021.129498 ↗
22. Modification of material properties and coating deposition using plasma jets
23. Berkovich, I.I., and Gromakovskiy, D.G. (2000). Tribologiya. Fizicheskiye osnovy, mekhanika i tekhnicheskiye prilozheniya: Uchebnik dlya vuzov., Samar. Gos. Tekhnicheskiy Univ. (In Russia).