Evaluation of Thermoelectric Performance of Bi2Te3 Films as a Function of Temperature Increase Rate during Heat Treatment
Source abstract
Abstract
Thin film thermoelectric generators are expected to be applied as power supplies for various Internet of Thing devices owing to their small size and flexible structure. However, the primary challenges of thin film thermoelectric generators are to improve their thermoelectric performance and reduce their manufacturing cost. Hence, Bi2Te3 thin films were deposited using direct current magnetron sputtering, followed by heat treatment at 573 K with different temperature increase rates ranging from 4 to 16 K/min. The in-plane Seebeck coefficient and electrical conductivity were measured at approximately 293 K. The in-plane thermal conductivity was calculated using the models to determine the power factor (PF) and dimensionless figure of merit (ZT). The temperature increase rate clearly affected the atomic composition, crystal orientation, and lattice strains, but not the crystallite size. The PF and dimensionless ZT increased as the temperature increase rate increased. The highest PF of 17.5 µW/(cm·K2) and ZT of 0.48 were achieved at a temperature increase rate of 16 K/min, while the unannealed thin film exhibited the lowest PF of 0.7 µW/(cm·K2) and ZT of 0.05. Therefore, this study demonstrated a method to enhance the thermoelectric performance of Bi2Te3 thin films by heat treatment at the appropriate temperature increase rate.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Thermoelectric Materials and Devices · Thermal properties of materials · Thermal Radiation and Cooling Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Materials Science, Tokai University, 4-1-1 Kitakaname, Hiratsuka, Kanagawa 259-1292, Japan
Funding
JSPS KAKENHI
References (77)
Show source-provided references
1. Thin-film thermoelectric devices with high room-temperature figures of merit10.1038/35098012 ↗
2. Thermoelectric performance of a metastable thin-film Heusler alloy10.1038/s41586-019-1751-9 ↗
3. Giant thermoelectric Seebeck coefficient of a two-dimensional electron gas in SrTiO310.1038/nmat1821 ↗
4. Ultralow thermal conductivity and high thermoelectric figure of merit in SnSe crystals10.1038/nature13184 ↗
5. Growth of single-crystalline Bi2Te3 hexagonal nanoplates with and without single nanopores during temperature-controlled solvothermal synthesis10.1038/s41598-019-47356-5 ↗
6. High-performance flexible bismuth telluride thin film from solution processed colloidal nanoplates
7. Facile preparation of air-stable n-type thermoelectric single-wall carbon nanotube films with anionic surfactants10.1038/s41598-020-64959-5 ↗
8. Flexible thermoelectric films formed using integrated nanocomposites with single-wall carbon nanotubes and Bi2Te3 nanoplates via solvothermal synthesis10.1038/s41598-020-73808-4 ↗
9. Novel hybrid organic thermoelectric materials: Three-component hybrid films consisting of a nanoparticle polymer complex, carbon nanotubes, and vinyl polymer10.1002/adma.201405463 ↗
10. Yamamuro, H., Hatsuta, N., Wachi, M., Takei, Y., and Takashiri, M. (2018). Combination of electrodeposition and transfer processes for flexible thin-film thermoelectric generators. Coatings, 8.10.3390/coatings8010022 ↗
11. Thermoelectric converters of human warmth for self-powered wireless sensor nodes10.1109/JSEN.2007.894917 ↗
12. Design and experimental investigation of a low-voltage thermoelectric energy harvesting system for wireless sensor nodes10.1016/j.enconman.2017.01.049 ↗
13. Flexible thermoelectric materials and device optimization for wearable energy harvesting10.1039/C5TC01644D ↗
14. Thermoelectric energy harvesting of human body heat for wearable sensors10.1109/JSEN.2013.2252526 ↗
15. Experimental and first-principles study of the electronic transport properties of strained Bi2Te3 thin films on a flexible substrate10.1063/1.4963875 ↗
16. Empirical modelling and optimization of pre-heat temperature and Ar flow rate using response surface methodology for stoichiometric Sb2Te3 thin films prepared by RF magnetron sputtering10.1016/j.jallcom.2017.04.322 ↗
17. Determining the thermal conductivity of nanocrystalline bismuth telluride thin films using the differential 3ω method while accounting for thermal contact resistance10.1007/s11664-015-3646-3 ↗
18. Lift-off patterning of thermoelectric thick films deposited by a thermally assisted sputtering method10.7567/APEX.7.057101 ↗
19. Optimization of the electrodeposition process of high-performance bismuth antimony telluride compounds for thermoelectric applications10.1021/la101952y ↗
20. Enhanced thermoelectric properties of electrodeposited Bi2Te3 thin films using TiN diffusion barrier layer on a stainless-steel substrate and thermal annealing10.1016/j.tsf.2020.138356 ↗
21. Microstructure and thermoelectric properties of p-type Bi-Sb-Te-Se thin films prepared by electrodeposition method10.1016/j.tsf.2011.10.020 ↗
22. Dual-bath electrodeposition of n-type Bi-Te/Bi-Se multilayer thin films10.1016/j.jallcom.2015.07.166 ↗
23. Determination of the origin of crystal orientation for nanocrystalline bismuth telluride-based thin films prepared by use of the flash evaporation method10.1007/s11664-013-2896-1 ↗
24. Fabrication by coaxial-type vacuum arc evaporation method and characterization of bismuth telluride thin films10.1007/s11664-012-2438-2 ↗
25. Bismuth antimony telluride thin films with unique crystal orientation by two-step method10.1016/j.jallcom.2016.05.058 ↗
26. High Seebeck coefficient in thermally evaporated Sb-In co-alloyed bismuth telluride thin film10.1063/1.5127108 ↗
27. Growth of single-crystalline bismuth antimony telluride nanoplates on the surface of nanoparticle thin films10.1016/j.jcrysgro.2013.03.028 ↗
28. Fabrication of bismuth telluride thermoelectric films containing conductive polymers using a printing method10.1007/s11664-012-2420-z ↗
29. Fabrication of bismuth telluride nanoplates via solvothermal synthesis using different alkalis and nanoplate thin films by printing method10.1016/j.jcrysgro.2016.12.048 ↗
30. Influences of substrate types and heat treatment conditions on structural and thermoelectric properties of nanocrystalline Bi2Te3 thin films formed by DC magnetron sputtering10.1016/j.vacuum.2020.109535 ↗
31. Annealing effects on the structural and electrical transport properties of n-type Bi2Te2.7Se0. 3 thin films deposited by flash evaporation10.1016/j.apsusc.2010.05.069 ↗
32. Effects of post-annealing on thermoelectric properties of bismuth-tellurium thin films deposited by co-sputtering10.1016/j.mee.2010.06.036 ↗
33. Effects of homogeneous irradiation of electron beam on crystal growth and thermoelectric properties of nanocrystalline bismuth selenium telluride thin films10.1016/j.jallcom.2014.05.146 ↗
34. Comparison of crystal growth and thermoelectric properties of n-type Bi-Se-Te and p-type Bi-Sb-Te nanocrystalline thin films: Effects of homogeneous irradiation with an electron beam10.1063/1.4881676 ↗
35. Thermoelectric effect in laser annealed printed nanocrystalline silicon layers10.1002/pssr.200701198 ↗
36. Influence of annealing on the structural and electrical transport properties of Bi0.5Sb1.5Te3.0 thin films deposited by co-sputtering10.1007/s10853-013-7259-z ↗
37. Thermal annealing effect on structural and thermoelectric properties of hexagonal Bi2Te3 nanoplate thin films by drop-casting technique10.7567/JJAP.57.02CC02 ↗
38. Thermoelectric properties of nanocrystalline Sb2Te3 thin films: Experimental evaluation and first-principles calculation, addressing effect of crystal grain size10.1088/1361-6528/aaa31f ↗
39. Effect of doping and annealing on thermoelectric properties of bismuth telluride thin films10.1007/s11664-020-08126-6 ↗
40. Effect of thermal annealing on the structural and thermoelectric properties of electrodeposited antimony telluride thin films10.1016/j.jallcom.2016.05.268 ↗
41. Effect of grain size on thermoelectric properties of n-type nanocrystalline bismuth-telluride based thin films10.1063/1.2990774 ↗
42. Effect of rapid thermal annealing on thermoelectric properties of bismuth telluride films grown by co-sputtering10.1016/j.mseb.2006.03.034 ↗
43. Effect of annealing and heating/cooling rate on the transformation temperatures of NiFeGa alloy10.1016/j.jallcom.2008.03.063 ↗
44. Effects of annealing temperature and heating rate on microstructure, magnetic, and mechanical properties of high-Bs Fe81.7-xSi4B13Nb xCu1.3 nanocrystalline alloys10.1007/s10853-020-05341-8 ↗
45. Impact of high heating rate, low temperature, and short time annealing on the realization of low resistivity Cu wire10.2320/matertrans.M2010133 ↗
46. The effects of annealing temperature and heating rate on Ta/TbFeCo bilayers10.1063/1.5129098 ↗
47. The use of semiconductors in thermoelectric refrigeration10.1088/0508-3443/5/11/303 ↗
48. Preparation and some physical properties of Bi2Te3, Sb2Te3, and As2Te310.1016/0022-3697(57)90081-1 ↗
49. Electrical and thermal properties of Bi2Te310.1103/PhysRev.108.1164 ↗
50. Anisotropic galvanomagnetic and thermoelectric properties of n-type Bi2Te3 single crystal with the composition of a useful thermoelectric cooling material10.1016/0022-3697(89)90045-0 ↗
51. Compound tellurides and their alloys for Peltier cooling10.1016/0038-1101(72)90172-4 ↗
52. Highly oriented crystal growth of nanocrystalline bismuth telluride thin films with anisotropic thermoelectric properties using two-step treatment10.1016/j.jallcom.2016.12.284 ↗
53. Mele, P. (2019). Thermoelectric Thin Films: Materials and Devices, Springer. Chapter 1.10.1007/978-3-030-20043-5 ↗
54. Theoretical and experimental analyses to determine the effects of crystal orientation and grain size on the thermoelectric properties of oblique deposited bismuth telluride thin films10.7567/JJAP.57.06HE02 ↗
55. Optimized structure of tubular thermoelectric generators using n-type Bi2Te3 and p-type Sb2Te3 thin films on flexible substrate for energy harvesting10.1016/j.sna.2020.112199 ↗
56. Recrystallization and grain growth10.1016/0502-8205(52)90009-9 ↗
57. Topotactical reactions with ferrimagnetic oxides having hexagonal crystal structures10.1016/0022-1902(59)80070-1 ↗
58. Orientation distribution–Lotgering factor relationship in a polycrystalline material—as an example of bismuth titanate prepared by a magnetic field10.2109/jcersj2.118.921 ↗
59. Measurement of thermal boundary resistance and thermal conductivity of single-crystalline Bi2Te3 nanoplate films by differential 3ω method10.35848/1882-0786/ab6e0e ↗
60. Vertical/planar growth and surface orientation of Bi2Te3 and Bi2Se3 topological insulator nanoplates10.1021/acs.nanolett.5b00240 ↗
61. Synthesis of polycrystalline nanotubular Bi2Te310.1016/j.matchemphys.2008.07.121 ↗
62. Combined effect of nanoscale grain size and porosity on lattice thermal conductivity of bismuth-telluride-based bulk alloys10.1063/1.4759326 ↗
63. Rowe, D.M. (1995). Thermoelectric Materials. CRC Handbook of Thermoelectrics, CRC Press.
64. Structural and thermoelectric properties of fine-grained Bi0.4Te3.0Sb1.6 thin films with preferred orientation deposited by flash evaporation method10.1016/j.tsf.2007.12.130 ↗
65. Investigation of the effects of compressive and tensile strain on n-type bismuth telluride and p-type antimony telluride nanocrystalline thin films for use in flexible thermoelectric generators10.1016/j.jallcom.2015.09.039 ↗
66. Characterization of Lorenz number with Seebeck coefficient measurement10.1063/1.4908244 ↗
67. Lower limit to the lattice thermal conductivity of nanostructured Bi2Te3-based materials10.1063/1.3226884 ↗
68. Cross-plane thermal conductivity of highly oriented nanocrystalline bismuth antimony telluride thin films10.1016/j.jallcom.2009.10.117 ↗
69. Evaluation of specific heat, sound velocity and lattice thermal conductivity of strained nanocrystalline bismuth antimony telluride thin films10.1007/s11664-014-3518-2 ↗
70. Effects of pre-stress and surface stress on phonon thermal conductivity of rectangular Si nanowires10.1007/s00339-014-8958-2 ↗
71. Strain and grain size effects on thermal transport in highly-oriented nanocrystalline bismuth antimony telluride thin films10.1016/j.ijheatmasstransfer.2014.04.048 ↗
72. Anisotropic analysis of nanocrystalline bismuth telluride thin films treated by homogeneous electron beam irradiation10.2320/matertrans.M2016295 ↗
73. Improved thermoelectric performance of highly-oriented nanocrystalline bismuth antimony telluride thin films10.1016/j.tsf.2010.08.013 ↗
74. Enhancement of thermoelectric properties of bismuth telluride composite with gold nano-particles inclusions using electrochemical co-deposition10.1149/2.1011912jes ↗
75. Thermoelectric properties of Bi2Te3-based thin films with fine grains fabricated by pulsed laser deposition10.1143/JJAP.48.085506 ↗
76. Control of p-type and n-type thermoelectric properties of bismuth telluride thin films by combinatorial sputter coating technology10.1016/j.apsusc.2017.02.187 ↗
77. Tailoring nanoporous structures in Bi2Te3 thin films for improved thermoelectric performance10.1021/acsami.9b13920 ↗