Modeling of Erosion Response of Cold-Sprayed In718-Ni Composite Coating Using Full Factorial Design
Source abstract
Abstract
In this work, the cold-spray technique was used to deposit Inconel 718–nickel (1:1) composite coatings on stainless steel substrate. A general full factorial design was adopted to identify the statistically significant operating variables, i.e., impingement angle, erodent size, and feed rate on the coating erosion response. Erodent feed rate, impingement angle, and the interaction between impingement angle and erodent size were identified as the highly significant variables on the erosion rate. Then, a model correlating the identified variables with the erosion rate was derived. The best combination of control variables for minimum erosion loss with respect to erodent feed rate, erodent size, and impingement angle was 2 mg/min, 60 μm, and 90°, respectively. To analyze the erosion mechanism, the erodent samples were finally observed using Scanning Electron Microscope (SEM).
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Erosion and Abrasive Machining · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Management and Production Engineering, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino, Italy
Mechanical and Industrial Engineering Department, University of Rome “ROMA TRE”, Via Vasca Navale 79, 00146 Rome, Italy
Department of Mechanical and Manufacturing Engineering, Trinity College Dublin, The University of Dublin, Parsons Building, Dublin 2 D02 PN40, Ireland
References (45)
Show source-provided references
1. Totten, G.E. (1992). ASM Handbook, Volume 18: Friction, Lubrication, and Wear Technology, ASM International.
2. Slurry Erosion Performance of Ni-Al2O3 Based Thermal-Sprayed Coatings: Effect of Angle of Impingement10.1007/s11666-013-0013-x ↗
3. Performance evaluation of HVOF deposited cermet coatings under dry and slurry erosion10.1016/j.surfcoat.2016.05.039 ↗
4. High temperature erosion wear of flame and plasma-sprayed nickel–chromium coatings under simulated coal-fired boiler atmospheres10.1016/S0043-1648(00)00540-8 ↗
5. An investigation on erosion behavior of HVOF sprayed WC–CoCr coatings10.1016/j.apsusc.2011.09.079 ↗
6. Parametric optimization of erosive wear response of TiAlN-coated aluminium alloy using Taguchi method10.1007/s11665-018-3816-6 ↗
7. Optimization and erosion wear response of NiCrSiB/WC–Co HVOF coating using Taguchi method10.1016/j.ceramint.2015.09.036 ↗
8. Development, characterization and erosion wear response of plasma sprayed fly ash–aluminum coatings10.1016/j.matdes.2009.09.039 ↗
9. Cold spraying of WC-Co-Ni coatings using porous WC-17Co powders: Formation mechanism, microstructure characterization and tribological performance10.1016/j.matdes.2017.04.040 ↗
10. Effects of substrate roughness and spray-angle on deposition behavior of cold-sprayed Inconel 71810.1016/j.surfcoat.2017.03.072 ↗
11. Wear and Corrosion Resistance of Cold-Sprayed Cu-Based Composite Coatings on Magnesium Substrate10.1007/s11666-019-00887-9 ↗
12. Cold spray forming of Inconel 71810.1007/s11666-012-9827-1 ↗
13. Effects of substrate heat accumulation on the cold sprayed Ni coating quality: Microstructure evolution and tribological performance10.1016/j.surfcoat.2019.04.090 ↗
14. Metallurgical control of fatigue crack propagation in superalloys10.1007/BF03220467 ↗
15. Studies of standard heat treatment effects on microstructure and mechanical properties of laser net shape manufactured Inconel 71810.1007/s11661-009-9949-3 ↗
16. Investigation of process factors affecting mechanical properties of INCONEL 718 superalloy in wire+ arc additive manufacture process10.1016/j.jmatprotec.2018.10.023 ↗
17. Structure of aluminum powder coatings prepared by cold gasdynamic spraying10.1007/BF01401446 ↗
18. Marrocco, T., McCartney, D., Shipway, P., and Sturgeon, A.J. (2006). Comparison of the microstructure of cold sprayed and thermally sprayed IN718 coatings. Thermal Spray 2006: Building on 100 Years of Success, Proceedings of the 2006 International Thermal Spray Conference, Seattle, WA, USA, 15–18 May, ASM International.10.31399/asm.cp.itsc2006p0265 ↗
19. Strategy of incorporating Ni-based braze alloy in cold sprayed Inconel 718 coating10.1016/j.surfcoat.2018.12.050 ↗
20. Pressureless sintering of cold sprayed Inconel 718 deposit10.1016/j.msea.2012.06.097 ↗
21. Microstructural evolution of cold-sprayed Inconel 625 superalloy coatings on low alloy steel substrate10.1016/j.actamat.2017.02.070 ↗
22. Thermal fatigue behavior of thermal barrier coatings with the MCrAlY bond coats by cold spraying and low-pressure plasma spraying10.1016/j.surfcoat.2010.08.144 ↗
23. Deposition behavior of thermally softened copper particles in cold spraying10.1016/j.actamat.2013.04.041 ↗
24. A comprehensive review of solid particle erosion modeling for oil and gas wells and pipelines applications10.1016/j.jngse.2014.10.001 ↗
25. Montgomery, D.C. (2017). Design and Analysis of Experiments, John Wiley & Sons. [9th ed.].
26. Erosive wear behavior of cold-sprayed Ni-WC composite coating10.1016/j.wear.2017.01.052 ↗
27. Microstructure and cavitation erosion performance of nickel-Inconel 718 composite coatings produced with cold spray10.1016/j.surfcoat.2019.125195 ↗
28. Comparison design of experiment (doe): Taguchi method and full factorial design in surface roughness10.4028/www.scientific.net/AMM.660.275 ↗
29. Parametric optimization of heat transfer from triangular fin array within a rectangular enclosure using design of experiment (DOE): A comparative analysis
30. Cold spray deposition to prevent fouling of polymer surfaces10.1080/02670844.2016.1229833 ↗
31. Wear by hard particles10.1016/S0301-679X(98)00079-6 ↗
32. Kuhn, H., and Medlin, D. (2000). Solid particle erosive wear testing. ASM Handbook. Mechanical Testing and Evaluation, ASM International.10.31399/asm.hb.v08.9781627081764 ↗
33. (2018). ASTM G76—18 Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets, ASTM International.
34. Mason, R.L., Gunst, R.F., and Hess, J.L. (2003). Statistical Design and Analysis of Experiments: With Applications to Engineering and Science, John Wiley & Sons. [2nd ed.].10.1002/0471458503 ↗
35. Montgomery, D.C., Runger, G.C., and Hubele, N.F. (2009). Engineering Statistics, John Wiley & Sons.
36. Champagne, V.K. (2007). The Cold Spray Materials Deposition Process, Woodhead Publishing.10.1533/9781845693787 ↗
37. An investigation of impingement erosion using single particles10.1016/0043-1648(72)90257-8 ↗
38. Critical impact velocity in the solid particles impact erosion of metallic materials10.1016/S0043-1648(99)00170-2 ↗
39. The effect of erodent particle characteristics on the erosion of metals10.1016/0043-1648(91)90263-T ↗
40. Hutchings, I.M. (1979). Mechanisms of the erosion of metals by solid particles. Erosion: Prevention and Useful Applications, ASTM International.10.1520/STP35795S ↗
41. Devore, J.L. (2011). Probability and Statistics for Engineering and the Sciences, Cengage Learning.
42. Performance of using multiple stepwise algorithms for variable selection10.1002/sim.3943 ↗
43. FEM analysis of the dependency on impact angle during erosive wear10.1016/S0043-1648(99)00174-X ↗
44. Melting at particle impact sites during erosion of ceramics10.1016/0043-1648(78)90066-2 ↗
45. Cavitation erosion and jet impingement erosion mechanism of cold sprayed Ni–Al2O3 coating10.1016/j.nucengdes.2011.09.038 ↗