Powder Properties and Processing Conditions Affecting Cold Spray Deposition
Source abstract
Abstract
The cold spray coating properties and performances are largely affected by feedstock characteristics and the employed processing parameters. Starting from experimental results obtained from the bibliographic data, the relationships between starting particles, processing conditions, and coating properties obtained by cold gas spray were analyzed. The relationships among these properties and particle velocity were described for various material systems. The effect on particle flattening, hardness, and porosity were largely described. Finally, the influence of the different parameters on the process output and on the coating properties was analytically defined through the employment of the multi-objective simulation tool modeFRONTIER. The analysis of data from the bibliography is a new trend that can also be applied to cold spray in order to analyze the effect of powder properties and spraying parameters on the cold spray (CS) process.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High-Temperature Coating Behaviors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Thermal Spray Centre (CPT), Dto. CMiQF. Universitat de Barcelona, C/Marti i Franques 1, 08028 Barcelona, Spain
Department of Engineering for Innovation, University of Salento, 73100 Lecce, Italy
References (91)
Show source-provided references
1. Cold gas dynamic spray technology: A comprehensive review of processing conditions for various technological developments till to date
2. Cold spray additive manufacturing and repair: Fundamentals and applications
3. Elucidation of cold-spray deposition mechanism by auger electron spectroscopic evaluation of bonding interface oxide film10.1016/j.actamat.2018.09.041 ↗
4. Adiabatic shear instability is not necessary for adhesion in cold spray10.1016/j.actamat.2018.07.065 ↗
5. Computational analysis of the interfacial bonding between feed-powder particles and the substrate in the cold-gas dynamic-spray process10.1016/S0169-4332(03)00643-3 ↗
6. Crystallization evolution of cold-sprayed pure Ni coatings10.1007/s11666-016-0430-8 ↗
7. Microstructural characterisation of titanium coatings deposited using cold gas spraying on Al2O3 substrates10.1016/j.surfcoat.2009.03.054 ↗
8. Optimization adhesion in cold spraying onto hard substrates: A case study for brass coatings10.1007/s11666-018-0821-0 ↗
9. Fatigue behavior of cold sprayed metals and alloys: A critical review10.1179/1743294415Y.0000000100 ↗
10. Gas flow, particle acceleration, and heat transfer in cold spray: A review10.1007/s11666-016-0406-8 ↗
11. Size-dependent distributions of particle velocity and temperature at impact in the cold-gas dynamic-spray process10.1016/j.jmatprotec.2014.09.013 ↗
12. Influence of powder injection parameters in high-pressure cold spray10.1007/s11666-017-0606-x ↗
13. Krull, F., Hesse, R., Breuninger, P., and Antonyuk, S. (2018). Impact behaviour of microparticles with microstructured surfaces: Experimental study and DEM simulation. Chem. Eng. Res. Des., 175–184.10.1016/j.cherd.2018.05.033 ↗
14. CFDEM modelling of particle heating and acceleration in cold spraying10.1016/j.ijrmhm.2018.02.003 ↗
15. Cold spraying—A materials perspective10.1016/j.actamat.2016.06.034 ↗
16. The effect of cold spray impact velocity on deposit hardness10.1088/0965-0393/18/6/065011 ↗
17. On parameter selection in cold spraying10.1007/s11666-011-9662-9 ↗
18. Numerical study of combination parameters for particle impact velocity and temperature in cold spray10.1007/s11666-007-9087-7 ↗
19. Microstructure of kinetic spray coatings: A review10.1007/s11666-015-0223-5 ↗
20. Review of relationship between particle deformation, coating microstructure, and properties in high-pressure cold spray10.1007/s11666-017-0575-0 ↗
21. Deposition of composite coatings by cold spray using stainless steel 316L, copper and tribaloy T-700 powder mixtures10.1016/j.surfcoat.2015.12.065 ↗
22. Huang, J., Ma, W., Xie, Y., Fukanum, H., Zhang, K., Wang, G., and Huang, R. (2019). Influence of cold gas spray processing conditions on the properties of 316L stainless steel coatings. Surf. Eng., 1–8.10.1080/02670844.2019.1584967 ↗
23. Mechanical properties of thick 304L stainless steel deposits processed by He cold spray10.1016/j.surfcoat.2015.07.001 ↗
24. On the formation of metallic glass coatings by means of cold gas spray technology10.1016/j.jallcom.2015.07.270 ↗
25. Residual stress and thermo-mechanical properties of cold spray metal coatings10.1016/j.actamat.2010.10.058 ↗
26. Cavaliere, P. (2018). Cold-Spray Coatings: Recent Trends and Future Perspectives, Springer.10.1007/978-3-319-67183-3 ↗
27. Particle velocity and deposition efficiency in the cold spray process10.1361/105996399770350278 ↗
28. Characterization of copper layers produced by cold gas-dynamic spraying10.1361/105996300770350087 ↗
29. Influence of nozzle throat dimension on microstructure and properties of cold sprayed coatings10.1007/s11666-019-00913-w ↗
30. Study of the influence of particle velocity on adhesive strength of cold spray deposits10.1007/s11666-011-9707-0 ↗
31. Development of ultra-strong adhesive strength coatings using cold spray10.1016/j.surfcoat.2014.07.074 ↗
32. Effect of processing conditions on porosity formation in cold gas dynamic spraying of copper10.1361/105996306X124437 ↗
33. Effect of injection pressure on particle acceleration, dispersion and deposition in cold spray10.1016/j.commatsci.2014.03.055 ↗
34. Particle loading effect in cold spray10.1361/105996306X108237 ↗
35. Cold sprayed Cu–Ni–Fe anode for Al production10.1016/j.corsci.2014.10.021 ↗
36. Measurement and numerical simulation of particle velocity in cold spraying10.1361/105996306X146956 ↗
37. Residual stresses in cold spray Al coatings: The effect of alloying and of process parameters10.1016/j.surfcoat.2012.04.034 ↗
38. Integrated characterization of cold sprayed aluminum coatings10.1016/j.actamat.2006.09.006 ↗
39. Aluminum coatings via kinetic spray with relatively large powder particles10.1016/S0257-8972(02)00018-X ↗
40. Cold spray Al-5% mg coatings for the corrosion protection of magnesium alloys10.1007/s11666-011-9675-4 ↗
41. Parameters of the gas-powder supersonic jet in cold spraying using a mask10.1007/s11666-013-9891-1 ↗
42. Estimating the effect of helium and nitrogen mixing on deposition efficiency in cold spray10.1007/s11666-016-0394-8 ↗
43. Cold spraying of Al–Sn binary alloy: Coating characteristics and particle bonding features10.1016/j.surfcoat.2007.07.026 ↗
44. Deposition characteristics of Al–12Si alloy coating fabricated by cold spraying with relatively large powder particles10.1016/j.apsusc.2007.02.142 ↗
45. Elimination of porosity in directly fabricated titanium via cold gas dynamic spraying10.1016/j.jmatprotec.2008.03.005 ↗
46. The effect of deposition conditions on adhesion strength of Ti and Ti6Al4V cold spray splats10.1007/s11666-011-9720-3 ↗
47. Influence of helium and nitrogen gases on the properties of cold gas dynamic sprayed pure titanium coatings10.1007/s11666-010-9568-y ↗
48. Deposition characteristics of titanium coating in cold spraying10.1016/S0257-8972(02)00919-2 ↗
49. Production of titanium deposits by cold-gas dynamic spray: Numerical modeling and experimental characterization10.1361/105996306X108219 ↗
50. Mechanical property mapping of cold sprayed Ti splats and coatings10.1007/s11666-010-9546-4 ↗
51. Comparison of oxidation and microstructure of warm-sprayed and cold-sprayed titanium coatings10.1007/s11666-011-9703-4 ↗
52. Mechanical and microstructural characterization of cold-sprayed Ti–6Al–4V after heat treatment10.1007/s11666-013-9945-4 ↗
53. Effects of working gas on wear and corrosion resistances of cold sprayed Ti–6Al–4V coatings10.1016/j.surfcoat.2016.05.052 ↗
54. Influence of feedstock powder and cold spray processing parameters on microstructure and mechanical properties of Ti–6Al–4V cold spray depositions10.1016/j.surfcoat.2017.12.014 ↗
55. Synthesis and mechanical properties of nanocrystalline Ni coatings produced by cold gas dynamic spraying10.1016/j.surfcoat.2006.01.037 ↗
56. CoNiCrAlY microstructural changes induced during cold gas dynamic spraying10.1016/j.surfcoat.2008.09.014 ↗
57. Cold-sprayed nanostructured pure cobalt coatings10.1007/s11666-016-0434-4 ↗
58. The effect of traverse speed on deposition efficiency of cold sprayed stellite 2110.1016/j.surfcoat.2019.03.012 ↗
59. Cold spray forming of inconel 71810.1007/s11666-012-9827-1 ↗
60. Microstructural and mechanical properties of high-performance Inconel 718 alloy by cold spraying10.1016/j.jallcom.2019.04.045 ↗
61. Microstructural and fatigue behavior of cold sprayed Ni-based superalloys coatings10.1016/j.surfcoat.2017.06.006 ↗
62. Microstructural evolution of cold-sprayed Inconel 625 superalloy coatings on low alloy steel substrate10.1016/j.actamat.2017.02.070 ↗
63. Effect of spray conditions on deposition behavior and microstructure of cold sprayed Ni coatings sprayed with a porous electrolytic Ni powder10.1016/j.surfcoat.2016.01.058 ↗
64. Investigation on the influence of particle preheating temperature on bonding of cold-sprayed nickel coatings10.1016/j.surfcoat.2016.09.037 ↗
65. Analysis of tantalum coatings produced by the kinetic spray process
66. Strong effect of carrier gas species on particle velocity during cold spray processes10.1016/j.surfcoat.2014.04.039 ↗
67. Cold spray characteristics of commercially pure Ti and Ti–6Al–4V10.4028/www.scientific.net/AMR.89-91.639 ↗
68. Multi-objective optimization of steel nitriding
69. Steel nitriding optimization through multi-objective and FEM analysis
70. Parametric study of exhaust pattern in cold spray using CFD and particle-wall impact analysis
71. An analysis of the cold spray process and its coatings10.1361/105996302770348682 ↗
72. On Some aspects of gas dynamics of the cold spray process10.1361/105996303770348384 ↗
73. Analysis of the impact velocity of powder particles in the cold-gas dynamic-spray process10.1016/j.msea.2003.10.312 ↗
74. Novel online diagnostic analysis for in-flight particle properties in cold spraying10.1007/s11666-018-0685-3 ↗
75. High strain rate deformation microstructures of stainless steel 316L by cold spraying and explosive powder compaction10.1007/s00339-007-4314-0 ↗
76. Effect of particle size on the microstructure and properties of kinetic sprayed nickel coatings10.1016/j.surfcoat.2010.03.046 ↗
77. Powder processing science and technology for increased reliability10.1111/j.1151-2916.1989.tb05945.x ↗
78. The unique abilities of cold spray deposition10.1080/09506608.2016.1194948 ↗
79. Measurements of cold spray deposition efficiency10.1361/105996306X124365 ↗
80. Diagnostics of cold-sprayed particle velocities approaching critical deposition conditions10.1007/s11666-017-0596-8 ↗
81. Deposition behavior, microstructure and mechanical properties of an in-situ micro-forging assisted cold spray enabled additively manufactured Inconel 718 alloy10.1016/j.matdes.2018.06.024 ↗
82. In-flight particle velocity measurements with DPV-2000 in cold spray10.1016/j.surfcoat.2006.04.035 ↗
83. Measurement of particle velocity and characterization of deposition in aluminum alloy kinetic spraying process10.1016/j.apsusc.2005.02.108 ↗
84. Dependency of deposition behavior, microstructure and properties of cold sprayed Cu on morphology and porosity of the powder10.1016/j.surfcoat.2017.08.070 ↗
85. Understanding the cold spray deposition efficiencies of 316L/Fe mixed powders by performing splat tests onto as-polished coatings10.1016/j.surfcoat.2017.05.083 ↗
86. Cold spray modeling and validation using an optical diagnostic method10.1016/j.surfcoat.2005.02.209 ↗
87. Microstructure and mechanical property of Ti and Ti6Al4V prepared by an in-situ shot peening assisted cold spraying10.1016/j.matdes.2015.07.015 ↗
88. Effect of particle morphology and size distribution on cold-sprayed pure titanium coatings10.1007/s11666-013-9951-6 ↗
89. Impact of high velocity cold spray particles10.1361/105996399770350250 ↗
90. Preparation of aluminum coatings containing homogenous nanocrystalline microstructures using the cold spray process10.1007/s11666-008-9180-6 ↗
91. Bonding mechanism in cold gas spraying10.1016/S1359-6454(03)00274-X ↗